
The AirTAC SEJ Adjustable Cylinder SEJ100X25-20S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 20mm window, so this Ø100mm unit covers an effective stroke of 5–25mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ100X25-20S is a double-acting, double-rod ISO 15552 profile cylinder with a 20 mm adjustable stroke window, yielding an effective travel range of 5 to 25 mm. A rod exits both ends, ensuring the annulus area remains identical in both directions for equal force and speed.
You dial in the exact retract end-position using a mechanical stop screw on the back rod, then lock it down—ideal for machine commissioning without swapping hardware. This extruded aluminum barrel omits external tie rods and includes field-adjustable air cushions at both ends to decelerate the 25 mm stroke smoothly.
| Model | Airtac SEJ Adjustable Cylinder SEJ100X25-20S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø100 mm |
| Nominal stroke | 25 mm |
| Adjustment window | 20 mm (5–25 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 20mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 3682 N |
| 0.7 MPa | 5154 N |
| Max (@1.0 MPa) | 751 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 100 | Bore size in mm. |
| ×25 | Nominal stroke length in mm. |
| -20 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 20 mm window to fine-tune the 5 to 25 mm forming depth on a stamping die, utilizing the 5153 N both-way force at 0.7 MPa to securely seat the workpiece.
Adjust the retract end-position on the fly when switching between varying box heights, relying on the equal push and pull forces to maintain consistent flap folding pressure.
Set precise 5 to 25 mm jaw travel limits during initial robot programming, locking the back-rod stop screw once the optimal grip on the 3681 N payload is achieved.
Verify the 20 mm adjustment window covers your positioning range; if you need less travel dialing, a fixed-stroke SED might suffice. For sizing both ways: the next bore down (80 mm) yields 2268 N at 0.5 MPa, while stepping up to 125 mm provides 5734 N. This 100 mm bore generates 3681 N both ways at 0.5 MPa.
The integrated magnet (-S) supports CMSE reed and DMSE electronic sensors for end-position confirmation. Remember, the adjustable stop screw sets the mechanical end and decelerates the load, but a plain SEJ does not hold position on air loss—specify an external rod lock for fail-safe holding. Ensure your ISO 15552 replacement matches the PT1/2 port, M20x1.5 rod thread, and mounting choice (Basic, FA, LB, TC, FTC, TCM1, or TCM2).
Quick checklist
The 20 mm adjustment window allows you to mechanically dial the retract stroke from 5 mm up to the nominal 25 mm. You set the exact end-position via a stop screw on the rear rod and lock it in place, which is ideal for fine-tuning during machine commissioning.
Because the rod exits both ends, force is equal in both directions: 3681 N at 0.5 MPa, 5153 N at 0.7 MPa, and a maximum of 751 kgf at 1.0 MPa. The cylinder also operates at speeds of 30-800 mm/s.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.