
The AirTAC SEJ Adjustable Cylinder SEJ100X350-75S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 75mm window, so this Ø100mm unit covers an effective stroke of 275–350mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ100X350-75S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 75 mm mechanical stroke adjustment window. A rod exits both ends, yielding an effective retract range of 275 to 350 mm. Because the piston sees identical annular areas on both sides, output force is perfectly symmetrical, delivering about 3681 N each way at 0.5 MPa.
A stop screw on the extended back rod lets you dial in the precise end position during machine commissioning without swapping hardware. The integrated -S magnet enables position detection with CMSE reed or DMSE electronic sensors, while field-adjustable air cushions at both ends manage deceleration over the 36 mm cushion length.
| Model | Airtac SEJ Adjustable Cylinder SEJ100X350-75S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø100 mm |
| Nominal stroke | 350 mm |
| Adjustment window | 75 mm (275–350 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 75mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 3682 N |
| 0.7 MPa | 5154 N |
| Max (@1.0 MPa) | 751 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 100 | Bore size in mm. |
| ×350 | Nominal stroke length in mm. |
| -75 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 75 mm back-rod stop to match varying die heights during press setup, using the 5153 N retract force to pull heavy tooling into the resting position safely.
Fine-tune the 275-350 mm stroke on the fly to align diverter arms for different pallet widths without changing out the cylinder hardware.
Adjust the retract end position to accommodate varying material thicknesses in a forming line, leveraging the equal both-way force for consistent clamping.
Verify this 75 mm adjustment window covers your required positioning range. If you need less force, the 80 mm bore provides 2268 N at 0.5 MPa; stepping up to the 125 mm bore yields 5734 N. If your end position never changes after setup, a fixed-stroke SED avoids the extra back-rod length. For replacing an ISO 15552 unit, match the 100 mm bore, 350 mm nominal stroke, PT1/2 port, and mounting style (Basic, FA, LB, TC, FTC, TCM1, or TCM2).
Because the nominal stroke is 350 mm, ensure external guides support the rod to prevent side-loading and premature seal wear. Note that the stop screw and air cushions only set the mechanical end and decelerate the load; they do not hold position on air loss. For fail-safe holding, specify an external rod lock.
Quick checklist
The retract stroke is mechanically adjustable via a stop screw on the back rod over a 75 mm window. This means your effective stroke can be dialed anywhere from 275 mm up to the full 350 mm. Once the desired end position is set, the screw is locked down.
Because it is a double-rod cylinder, the force is identical in both directions: 3681 N at 0.5 MPa, 5153 N at 0.7 MPa, and a maximum of 751 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.