
The AirTAC SEJ Adjustable Cylinder SEJ100X80-30S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 30mm window, so this Ø100mm unit covers an effective stroke of 50–80mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ100X80-30S is a double-acting, double-rod ISO 15552 profile cylinder with a 30mm adjustable stroke window. A rod exits both ends, yielding identical annulus areas so thrust is perfectly balanced at 3681 N each way at 0.5 MPa. You dial the retract end from 50mm up to the nominal 80mm.
A stop screw on the back rod lets you mechanically set the exact end position during machine commissioning. The integrated -S magnet supports CMSE reed and DMSE electronic sensors for precise tracking.
| Model | Airtac SEJ Adjustable Cylinder SEJ100X80-30S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø100 mm |
| Nominal stroke | 80 mm |
| Adjustment window | 30 mm (50–80 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 30mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 3682 N |
| 0.7 MPa | 5154 N |
| Max (@1.0 MPa) | 751 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 100 | Bore size in mm. |
| ×80 | Nominal stroke length in mm. |
| -30 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Delivering 5153 N at 0.7 MPa, this cylinder dials the press stroke from 50 to 80mm to perfectly seat bearings without changing hardware.
Adjust the retract end up to 30mm to accommodate different product heights on a single conveyor line, leveraging equal both-way force.
Use the back-rod stop screw to precisely set the mechanical end position during machine commissioning, locking it once the target is reached.
The 30mm adjustment window is ideal for fine-tuning a variable stop or matching a specific part height. If 3681 N at 0.5 MPa is excessive, step down to the 80mm bore which provides 2268 N both ways. For heavier payloads, the 125mm bore yields 5734 N at 0.5 MPa.
Because the stroke is 80mm, side-load risks are minimal, but always verify external guide alignment. The field-adjustable air cushion at both ends decelerates the payload near the stroke limits but does not hold position on air loss; for fail-safe holding, use an external rod lock. When replacing an ISO 15552 unit, match the PT1/2 port, M20x1.5 rod thread, and mounting subset (Basic, FA, LB, TC, FTC, TCM1, TCM2).
Quick checklist
The cylinder has a 30mm adjustment window, allowing you to dial the effective retract stroke from 50mm up to the nominal 80mm. You set the exact position via a stop screw on the back rod.
Because the rod exits both ends, force is equal in both directions: 3681 N at 0.5 MPa, 5153 N at 0.7 MPa, and a maximum of 751 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.