
The AirTAC SEJ Adjustable Cylinder SEJ100X80-75 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 75mm window, so this Ø100mm unit covers an effective stroke of 5–80mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ100X80-75 is a double-acting, double-rod ISO 15552 profile cylinder featuring a 75 mm adjustable stroke window. A rod exits both ends, yielding identical annulus areas so output force is equal in both directions at 3681 N each way at 0.5 MPa. You can dial the retract end-position down from the nominal 80 mm to a 5 mm effective stroke.
A stop screw on the back rod acts as the mechanical adjuster; set your exact end-position on the machine, then lock it. The extruded aluminum barrel has no external tie rods, and adjustable air cushions at both ends decelerate the 25 mm rod near stroke ends. This SKU has no magnet, so position sensing is not installed.
| Model | Airtac SEJ Adjustable Cylinder SEJ100X80-75 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø100 mm |
| Nominal stroke | 80 mm |
| Adjustment window | 75 mm (5–80 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 75mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 3682 N |
| 0.7 MPa | 5154 N |
| Max (@1.0 MPa) | 751 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 100 | Bore size in mm. |
| ×80 | Nominal stroke length in mm. |
| -75 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the retract stroke from 5 to 80 mm to perfectly set the metal feed stop on a mechanical press, utilizing 5153 N of both-way force at 0.7 MPa to push the stock.
Adjust the end position on the fly to accommodate different pallet heights without swapping hardware, relying on the equal push and pull force for stable actuation.
Fine-tune the exact clamping end-position during machine commissioning, locking the back-rod stop screw once the optimal 5 to 80 mm stroke is found.
Verify the 75 mm adjustment window covers your required retract range; here you can tune the end stop anywhere from 5 to 80 mm. Stepping down to the 80 mm bore drops the both-way force to 2268 N at 0.5 MPa, while moving up to the 125 mm bore increases it to 5734 N. If your positioning never changes after commissioning, a fixed-stroke SED avoids the back-rod hardware.
For a direct ISO 15552 replacement, match the 100 mm bore, 80 mm stroke, PT1/2 port, and your mounting choice from Basic, FA, LB, TC, FTC, TCM1, or TCM2. The adjustable air cushion is for deceleration only; it is not a lock. A plain SEJ does not hold position on air loss, so use a BSED or external rod lock for fail-safe hold.
Quick checklist
The 75 mm adjustment window lets you mechanically shorten the retract stroke from the 80 mm nominal down to a 5 mm effective stroke. You set the exact end-position via a stop screw on the back rod, then lock it in place.
Because the rod exits both ends, force is identical in both directions. It delivers 3681 N at 0.5 MPa, 5153 N at 0.7 MPa, and a maximum of 751 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.