
The AirTAC SEJ Adjustable Cylinder SEJ40X250-75S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 75mm window, so this Ø40mm unit covers an effective stroke of 175–250mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ40X250-75S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 75mm adjustable stroke window, yielding an effective travel range of 175-250mm. A piston rod exits both ends, ensuring the annular area is identical in both directions. This provides an equal output force of 528 N each way at 0.5 MPa, preventing speed discrepancies between extend and retract motions.
The retract end is mechanically regulated by a stop screw on the back rod, allowing you to dial in the exact end-position without changing mounting hardware. Equipped with a magnet for position sensing, this cylinder uses a PT1/4 port and a Ø16mm rod. It features field-adjustable air cushions at both ends to decelerate the load near stroke end, and its extruded aluminum barrel ensures clean integration without external tie rods.
| Model | Airtac SEJ Adjustable Cylinder SEJ40X250-75S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Nominal stroke | 250 mm |
| Adjustment window | 75 mm (175–250 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 75mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×250 | Nominal stroke length in mm. |
| -75 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the 175-250mm retract stop during machine setup to precisely strike a 528N press fit without re-machining hard stops.
Use the 75mm retract window to test gripper reach on a new CNC fixture, fine-tuning the end point before locking the mechanism.
Confirm the 75mm adjustment window covers your positioning range; this model effectively dials the retract stroke anywhere from 175mm up to the full 250mm. If your application requires less force, the adjacent SEJ32 bore provides 345 N at 0.5 MPa, whereas stepping up to the SEJ50 bore yields 825 N both ways. If you do not need variable end-positioning, a fixed-stroke SED cylinder is sufficient. Because the stroke is 250mm, external guides are recommended to prevent side-loading on the rod.
This unit is dimensionally interchangeable per ISO 15552, so verify your replacement parameters match the 40mm bore, 250mm nominal stroke, PT1/4 port, and magnet requirement. The adjustable air cushion decelerates the load near the stroke end but is not a lock. A plain SEJ does not hold position on air loss; for fail-safe holding, specify a BSED or an external rod lock. The included -S magnet supports CMSE reed and DMSE electronic sensors.
Quick checklist
The 75mm adjustment window allows you to mechanically shorten the retract stroke via a back-rod stop screw. The effective stroke range is 175mm to 250mm.
Because the rod exits both ends, force is equal in both directions. It provides 528 N at 0.5 MPa, 739 N at 0.7 MPa, and a maximum of 108 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.