verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SEJ Series · ISO 15552 Adjustable-Stroke Cylinder

Airtac SEJ Adjustable Cylinder SEJ50X175-50S

The AirTAC SEJ Adjustable Cylinder SEJ50X175-50S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 50mm window, so this Ø50mm unit covers an effective stroke of 125–175mm without changing cylinders. Force is equal in both directions.

  • BoreØ50 mm
  • Nominal stroke175 mm
  • Adjust window50 mm
  • Effective stroke125–175 mm
  • Port sizePT1/4
  • CushionAdjustable, 30 mm
$109.77 $117.27Save 6% Standard model — usually dispatched in 3-5 days
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Shipped from our own warehouse: most standard models dispatch in 3–5 days; custom and non-standard models take 8–10 business days. Transit time after that depends on the destination.
Compare every SEJ50 stroke, mounting and version on one page All SEJ50 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7 h

About the Airtac SEJ Adjustable Cylinder SEJ50X175-50S

The AirTAC SEJ50X175-50S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 50 mm adjustable stroke window. A rod exits both ends, yielding identical annulus areas so thrust is equal in both directions at 825 N each way at 0.5 MPa. The retract stroke dials in from 125 mm to 175 mm via a back-rod stop screw, letting you set the exact end position during commissioning without machining new mounts.

This extruded aluminum barrel omits external tie rods and includes field-adjustable air cushions at both ends to decelerate the 30 mm cushion zone near stroke extremes. Equipped with a standard magnet, it supports CMSE reed and DMSE electronic sensors for position feedback. It uses a PT1/4 port, a Ø20 mm rod, and an M16x1.5 rod-end thread.

Airtac SEJ Adjustable Cylinder SEJ50X175-50S Technical Specifications

ModelAirtac SEJ Adjustable Cylinder SEJ50X175-50S
SeriesSEJ ISO 15552 adjustable-stroke cylinder
Bore sizeØ50 mm
Nominal stroke175 mm
Adjustment window50 mm (125–175 mm)
ConfigurationDouble rod, double acting
Port sizePT1/4
Rod threadM16×1.5
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 30 mm

Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 50mm window. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø50mm)

PressureForce (both directions)
0.5 MPa825 N
0.7 MPa1155 N
Max (@1.0 MPa)168 kgf

A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.

Model Code: Airtac SEJ Adjustable Cylinder SEJ50X175-50S

SEJISO 15552 double-rod double-acting cylinder with adjustable stroke.
50Bore size in mm.
×175Nominal stroke length in mm.
-50Adjustment stroke window in mm (options: 10/20/30/40/50/75/100).
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).

Where the Airtac SEJ Adjustable Cylinder SEJ50X175-50S Is Used

straighten

Material Changeover

Dial the retract stroke from 125 to 175 mm to accommodate varying part heights on a conveyor transfer without swapping out the entire cylinder assembly.

tune

Press Fit Commissioning

Fine-tune the 825 N both-way clamping force end-stop precisely during machine setup to avoid over-travel when seating bearings or pins.

precision_manufacturing

End-Stop Truing

Lock the back-rod stop screw after micro-adjusting the 175 mm nominal position to perfectly match a fixed machine guard or mechanical dead stop.

Is the Airtac SEJ Adjustable Cylinder SEJ50X175-50S the Right Cylinder?

Confirm the 50 mm adjustment window covers your required end-position variance, providing an effective 125 to 175 mm stroke. If you need less fine-tuning and a fixed stop is sufficient, the standard SED double-rod cylinder is a simpler choice. Stepping down to the 40 mm bore yields 528 N both-way force at 0.5 MPa, while stepping up to the 63 mm bore provides 1402 N.

The adjustable air cushion and mechanical stop screw decelerate the load and set the end position, but a plain SEJ does not hold position on air loss. For fail-safe holding, specify a BSED or an external rod lock. Because the stroke is under 300 mm, side-load risks are lower, but always guide the load externally to prevent rod binding.

AirtacDistr lists every SEJ50 order code with its price on one page at https://airtacdistr.com/products/airtac-sej50-adjustable-cylinder

Quick checklist

  • ✓ Need on-machine stroke fine-tuning?
  • ✓ Adjustment window (50mm) covers your range
  • ✓ Equal force both directions OK
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Set the stop screw within the 50mm window; lock it after adjusting.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SEJ Adjustable Cylinder SEJ50X175-50S FAQ

The 50 mm adjustment window lets you dial the retract stroke down from the 175 mm nominal maximum to 125 mm. You set the exact end position via the back-rod stop screw, then lock it in place.

Because the rod exits both ends, force is equal in both directions: 825 N at 0.5 MPa, 1154 N at 0.7 MPa, and a maximum of 168 kgf at 1.0 MPa.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Most standard models are dispatched in 3-5 days.

bolt

Fast Reply

Most inquiries answered within 7 hours.

Related AirTAC SEJ Cylinders

Request a Quote for Airtac SEJ Adjustable Cylinder SEJ50X175-50S

Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.

Thank you. We received your request for SEJ50X175-50S and will confirm price, availability and lead time — usually within 7 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.