
The AirTAC SEJ Adjustable Cylinder SEJ63X100-75S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 75mm window, so this Ø63mm unit covers an effective stroke of 25–100mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ63X100-75S is a double-acting, double-rod ISO 15552 profile cylinder with a 75mm adjustable stroke window, letting you dial the retract end from 25mm up to 100mm. A rod exits both ends, yielding equal force in both directions at 1402 N each way at 0.5 MPa. The extruded aluminum barrel contains no external tie rods, ensuring clean integration.
You fine-tune the end position via a stop screw on the back rod, then lock it in place for precise machine commissioning. This bore uses a PT3/8 port, a Ø20 mm rod, and includes a magnet (-S) for CMSE reed or DMSE electronic sensors. Adjustable air cushions at both ends decelerate the load near stroke end.
| Model | Airtac SEJ Adjustable Cylinder SEJ63X100-75S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø63 mm |
| Nominal stroke | 100 mm |
| Adjustment window | 75 mm (25–100 mm) |
| Configuration | Double rod, double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 75mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 1402 N |
| 0.7 MPa | 1962 N |
| Max (@1.0 MPa) | 286 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 63 | Bore size in mm. |
| ×100 | Nominal stroke length in mm. |
| -75 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the retract stroke from 25 to 100mm to hit a precise material stop. The equal 1402N both-way force securely pushes and pulls the feed clamp without asymmetric drift.
Switch carton sizes by adjusting the back-rod stop screw rather than swapping hardware. The 75mm window covers varied box heights while the magnet enables DMSE electronic position tracking.
Set exact electrode touch points during machine commissioning. Lock the stop screw once positioned, relying on the 36mm adjustable air cushion to decelerate the rod before impact.
Verify the 75mm adjustment window covers your required positioning range. If you need less force, the 50mm bore provides 825 N both ways at 0.5 MPa; if you need more, stepping up to the 80mm bore yields 2268 N. If you never need to vary the stroke after setup, a fixed-stroke SED saves complexity.
This cylinder does not hold position on air loss, so use a BSED or external rod lock for fail-safe holding. For ISO 15552 replacement matching, confirm the 100mm stroke, 75mm window, PT3/8 port, and your mounting choice from Basic, FA, LB, TC, FTC, TCM1, or TCM2.
Quick checklist
The 75mm window lets you mechanically dial the retract end position down from the nominal 100mm stroke to a minimum effective stroke of 25mm. You set the exact end point via a stop screw on the back rod and lock it after positioning.
Because the rod exits both ends, force is identical in both directions: 1402 N at 0.5 MPa, 1962 N at 0.7 MPa, and a maximum of 286 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.