
The AirTAC SEJ Adjustable Cylinder SEJ63X150-50 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 50mm window, so this Ø63mm unit covers an effective stroke of 100–150mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ63X150-50 is a double-acting, double-rod ISO 15552 profile cylinder with a 50 mm adjustable retract window. A stop screw on the back rod lets you mechanically shorten the effective stroke anywhere from 100 mm up to 150 mm. Because a rod exits both ends, the annular area is identical in both directions, yielding an equal force of 1402 N each way at 0.5 MPa.
This extruded-aluminum barrel omits external tie rods and carries field-adjustable air cushions at both ends to decelerate the load near stroke end. The 63 mm bore uses a PT3/8 port and a 20 mm rod with an M16x1.5 thread. This specific SKU lacks a magnet, so it will not trigger CMSE or DMSE position sensors without modification.
| Model | Airtac SEJ Adjustable Cylinder SEJ63X150-50 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø63 mm |
| Nominal stroke | 150 mm |
| Adjustment window | 50 mm (100–150 mm) |
| Configuration | Double rod, double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 50mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 1402 N |
| 0.7 MPa | 1962 N |
| Max (@1.0 MPa) | 286 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 63 | Bore size in mm. |
| ×150 | Nominal stroke length in mm. |
| -50 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 50 mm retract window to set precise 100-150 mm die clearance during press changeovers, utilizing the 1402 N both-way force at 0.5 MPa to seat heavy tooling.
Fine-tune the mechanical stop position on a packaging line conveyor to handle varying carton lengths without swapping hardware, matching the stop precisely within the 50 mm window.
Adjust the retract end-point during trial positioning of a test specimen, using the equal 1962 N both-way force at 0.7 MPa to apply consistent clamping and release pressure.
Confirm the 50 mm adjustment window covers your required end-position range; here you can dial the retract stroke precisely between 100 mm and 150 mm. If you need less force, the adjacent 50 mm bore provides 825 N at 0.5 MPa both ways, while stepping up to the 80 mm bore yields 2268 N at 0.5 MPa both ways. If your end position never changes after commissioning, a fixed-stroke SED cylinder is sufficient and shorter overall.
When matching an ISO 15552 replacement, verify the 63 mm bore, 150 mm nominal stroke, PT3/8 port, and mounting choice from the SEJ subset (Basic, FA, LB, TC, FTC, TCM1, TCM2). The adjustable cushion is not a brake; a plain SEJ does not hold position on air loss, so for fail-safe holding look to a BSED or an external rod lock. At 150 mm stroke, side loading is minimal, but always ensure external guides support any heavy offset loads.
Quick checklist
A stop screw on the back rod mechanically shortens the retract stroke. For this model, the 50 mm window allows you to dial the effective stroke anywhere from 100 mm up to the full 150 mm, which you then lock in place.
Because the rod exits both ends, force is equal in both directions. It delivers 1402 N at 0.5 MPa, 1962 N at 0.7 MPa, and a maximum of 286 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.