
The AirTAC SEJ Adjustable Cylinder SEJ63X50-10S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 10mm window, so this Ø63mm unit covers an effective stroke of 40–50mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ63X50-10S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 10mm adjustable stroke window. A stop screw on the rear rod lets you dial the retract end, yielding an effective stroke range of 40-50mm for precision machine commissioning.
This 63mm bore unit uses a PT3/8 port and a Ø20 mm rod with an M16x1.5 thread. The included -S magnet enables position detection with CMSE reed or DMSE electronic sensors. Adjustable air cushions at both ends absorb kinetic energy near stroke end, while the extruded aluminum barrel ensures ISO 15552 dimensional interchangeability without external tie rods.
| Model | Airtac SEJ Adjustable Cylinder SEJ63X50-10S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø63 mm |
| Nominal stroke | 50 mm |
| Adjustment window | 10 mm (40–50 mm) |
| Configuration | Double rod, double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 10mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 1402 N |
| 0.7 MPa | 1962 N |
| Max (@1.0 MPa) | 286 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 63 | Bore size in mm. |
| ×50 | Nominal stroke length in mm. |
| -10 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 10mm retract window to perfectly seat custom gripper jaws on varying part sizes, utilizing the equal 1402 N clamping force both ways at 0.5 MPa.
Fine-tune the 40-50mm effective stroke on an assembly press to set precise bearing insertion depths without swapping mechanical hardware.
Adjust the retract end-stroke on the fly when a packaging line switches carton heights, relying on the double-rod design for consistent speed and force.
Verify the 10mm adjustment window covers your positioning range; the retract end sets from 40 to 50mm. If you need less thrust, the adjacent 50mm bore provides 825 N at 0.5 MPa, or step up to the 80mm bore for 2268 N. A fixed-stroke SED is sufficient if you never need to fine-tune the end position on the machine.
For a direct ISO 15552 replacement, match the 50mm nominal stroke, 10mm window, PT3/8 port, and your mounting choice (Basic, FA, LB, TC, FTC, TCM1, or TCM2). Note that the air cushion and mechanical stop screw decelerate the load but do not hold position on air loss; use an external rod lock for fail-safe holding.
Quick checklist
A stop screw on the rear rod mechanically shortens the retract stroke over a 10mm window. For this 50mm nominal stroke model, you can adjust the effective end position anywhere from 40mm to 50mm. You lock the screw after setting your desired position.
Because it is a double-rod cylinder, force is equal in both directions. It outputs 1402 N at 0.5 MPa, 1962 N at 0.7 MPa, and has a maximum capacity of 286 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.