
The AirTAC SEJ Adjustable Cylinder SEJ63X80-20 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 20mm window, so this Ø63mm unit covers an effective stroke of 60–80mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ63X80-20 is a double-acting, double-rod ISO 15552 profile cylinder offering an adjustable retract stroke. A rod exits both ends, yielding identical annulus areas so output force is equal in both directions at 1402 N each way at 0.5 MPa. An integrated stop screw on the back rod lets you dial the retract end up to 20 mm, providing an effective stroke range of 60-80 mm.
This extruded aluminum profile cylinder omits external tie rods and features field-adjustable air cushions at both ends to tame kinetic energy near stroke end. It uses a PT3/8 port, a Ø20 mm rod, and operates at speeds from 30-800 mm/s. This specific SKU lacks a magnet, so it does not support position sensing without modifying the build.
| Model | Airtac SEJ Adjustable Cylinder SEJ63X80-20 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø63 mm |
| Nominal stroke | 80 mm |
| Adjustment window | 20 mm (60–80 mm) |
| Configuration | Double rod, double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 20mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 1402 N |
| 0.7 MPa | 1962 N |
| Max (@1.0 MPa) | 286 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 63 | Bore size in mm. |
| ×80 | Nominal stroke length in mm. |
| -20 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 20 mm retract window to adapt a 1962 N clamping motion for varying carton depths without swapping hardware.
Fine-tune the 60-80 mm effective stroke on an assembly press to set precise bearing seating depth during machine commissioning.
Verify the 20 mm adjustment window safely covers your required end-position variance. If you need less force, the adjacent 50 mm bore provides 825 N at 0.5 MPa both ways; if you need more, step up to the 80 mm bore for 2268 N at 0.5 MPa. If your machine never requires stroke tuning, a fixed-stroke SED saves length and cost.
For direct ISO 15552 replacement, match the 63 mm bore, 80 mm nominal stroke, PT3/8 port, and your mounting choice from Basic, FA, LB, TC, FTC, TCM1, or TCM2. Note that the air cushion and stop screw decelerate the load but do not hold position on air loss; use an external rod lock for fail-safe holding.
Quick checklist
A stop screw on the rear rod mechanically shortens the retract stroke over a 20 mm window. You can set the effective stroke anywhere from 60 mm up to the full 80 mm, then lock it in place for precise end-position tuning.
Because it is a double-rod cylinder, the force is identical in both directions. It provides 1402 N at 0.5 MPa, 1962 N at 0.7 MPa, and a maximum of 286 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.