verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SEJ Series · ISO 15552 Adjustable-Stroke Cylinder

Airtac SEJ Adjustable Cylinder SEJ80X75-50S

The AirTAC SEJ Adjustable Cylinder SEJ80X75-50S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 50mm window, so this Ø80mm unit covers an effective stroke of 25–75mm without changing cylinders. Force is equal in both directions.

  • BoreØ80 mm
  • Nominal stroke75 mm
  • Adjust window50 mm
  • Effective stroke25–75 mm
  • Port sizePT3/8
  • CushionAdjustable, 36 mm
$151.64 $159.14Save 4% Standard model — usually dispatched in 3-5 days
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Shipped from our own warehouse: most standard models dispatch in 3–5 days; custom and non-standard models take 8–10 business days. Transit time after that depends on the destination.
Compare every SEJ80 stroke, mounting and version on one page All SEJ80 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7 h

About the Airtac SEJ Adjustable Cylinder SEJ80X75-50S

The AirTAC SEJ80X75-50S is a double-acting, double-rod ISO 15552 profile cylinder. A rod exits both ends, yielding identical annulus areas so thrust is equal in both directions at 2268 N each way at 0.5 MPa. The retract stroke is mechanically adjustable via a stop screw on the back rod over a 50 mm window, setting an effective stroke range of 25 to 75 mm.

This extruded aluminum barrel design omits external tie rods and includes field-adjustable air cushions at both ends to decelerate loads near stroke end. Equipped with a magnet, it supports CMSE reed and DMSE electronic sensors. The PT3/8 port and Ø25 mm rod provide robust pneumatic capacity for demanding positioning tasks.

Airtac SEJ Adjustable Cylinder SEJ80X75-50S Technical Specifications

ModelAirtac SEJ Adjustable Cylinder SEJ80X75-50S
SeriesSEJ ISO 15552 adjustable-stroke cylinder
Bore sizeØ80 mm
Nominal stroke75 mm
Adjustment window50 mm (25–75 mm)
ConfigurationDouble rod, double acting
Port sizePT3/8
Rod threadM20×1.5
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 36 mm

Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 50mm window. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø80mm)

PressureForce (both directions)
0.5 MPa2268 N
0.7 MPa3175 N
Max (@1.0 MPa)463 kgf

A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.

Model Code: Airtac SEJ Adjustable Cylinder SEJ80X75-50S

SEJISO 15552 double-rod double-acting cylinder with adjustable stroke.
80Bore size in mm.
×75Nominal stroke length in mm.
-50Adjustment stroke window in mm (options: 10/20/30/40/50/75/100).
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).

Where the Airtac SEJ Adjustable Cylinder SEJ80X75-50S Is Used

straighten

Board Trimming Stops

Dial the retract stop precisely to trim varying board widths, leveraging the 2268 N both-way force to shear materials cleanly.

tune

Machine Commissioning

Fine-tune the end-of-stroke position during machine setup, adjusting the 50 mm window to perfectly mate with existing tooling.

swap_horiz

Part Height Changeover

Quickly reconfigure press stops for different part heights using the back-rod adjustment, avoiding cylinder teardown.

Is the Airtac SEJ Adjustable Cylinder SEJ80X75-50S the Right Cylinder?

Verify the 50 mm adjustment window covers your required end-position range, allowing precise dial-in of the 25 to 75 mm effective stroke without changing hardware. If your application needs less force, stepping down to the 63 mm bore yields 1402 N at 0.5 MPa; if you need more, the 100 mm bore provides 3681 N at 0.5 MPa. For fixed-position tasks that never require stroke tuning, a standard SED double-rod cylinder is sufficient. Note that the air cushion and stop screw only set the mechanical end and decelerate the load; they do not hold position on air loss, so an external rod lock is required for fail-safe holding. At 75 mm stroke, side loads are minimal, but always ensure external guides support any lateral forces.

Quick checklist

  • ✓ Need on-machine stroke fine-tuning?
  • ✓ Adjustment window (50mm) covers your range
  • ✓ Equal force both directions OK
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Set the stop screw within the 50mm window; lock it after adjusting.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SEJ Adjustable Cylinder SEJ80X75-50S FAQ

The cylinder has a 50 mm adjustment window on the retract end, allowing the effective stroke to be dialed from 25 mm up to 75 mm. You set the position via a stop screw on the back rod and lock it after tuning.

Because the rod exits both ends, the force is equal in both directions. It generates 2268 N at 0.5 MPa, 3175 N at 0.7 MPa, and a maximum of 463 kgf at 1.0 MPa.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Most standard models are dispatched in 3-5 days.

bolt

Fast Reply

Most inquiries answered within 7 hours.

Related AirTAC SEJ Cylinders

Request a Quote for Airtac SEJ Adjustable Cylinder SEJ80X75-50S

Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.

Thank you. We received your request for SEJ80X75-50S and will confirm price, availability and lead time — usually within 7 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.