Airtac SGC Standard Cylinder SGC200X1000STC
The AirTAC Airtac SGC Standard Cylinder SGC200X1000STC is a genuine double acting ISO 15552 (orig. ISO 6431) tie-rod air cylinder with a Ø200mm bore and 1000mm stroke, G3/4 air ports and adjustable end cushioning. Its large-bore tie-rod build delivers high thrust and drops into standardized ISO 15552 mounting on heavy automation.
- BoreØ200 mm
- Stroke1000 mm
- Port sizeG3/4
- Acting typeDouble acting
- Rod threadM36×2.0
- CushionAdjustable, 50 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SGC Standard Cylinder SGC200X1000STC
Delivering 15708 N of push force at 0.5 MPa, this double-acting large-bore actuator is built around a genuine ISO 15552 mounting interface for seamless fixture integration. The SGC200X1000STC utilizes a robust tie-rod design where four steel rods clamp the aluminum barrel to the covers, ensuring high structural rigidity under heavy thrust. A heterogeneous two-way piston seal maintains an internal oil reservoir to maximize operational lifespan.
Equipped with a G3/4 port and a 1000 mm stroke, the unit features adjustable air cushions at both ends to absorb kinetic energy. For practical sizing, plan for roughly 9425 N of real work at 0.5 MPa, which equates to lifting about 801 kg vertically with a 2:1 safety margin. The included -S piston magnet enables CMSG, DMSG, or EMSG electronic switches for position sensing.
Airtac SGC Standard Cylinder SGC200X1000STC Technical Specifications
| Model | Airtac SGC Standard Cylinder SGC200X1000STC |
|---|---|
| Series | SGC ISO 15552 tie-rod cylinder |
| Bore size | Ø200 mm |
| Stroke | 1000 mm |
| Acting type | Double acting |
| Port size | G3/4 |
| Rod thread | M36×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Adjustable, 50 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC SGC datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Thread options: PT (blank) / G. TPU seals are not available for the Ø250 bore (NBR / Viton only).
Theoretical Output Force (Ø200mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 15708 N | 15080 N |
| 0.7 MPa | 21991 N | — |
| Max (@1.0 MPa) | 3204 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SGC Standard Cylinder SGC200X1000STC
| SGC | ISO 15552 tie-rod cylinder (double-acting type). |
|---|---|
| 200 | Bore size in mm (125 / 160 / 200 / 250). |
| ×1000 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
SGC-family variants: SGC (double acting), SGCD (double rod), SGCJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / FTC / TCM1 / TCM2. Seals: TPU (blank) / Viton H / NBR N.
Where the Airtac SGC Standard Cylinder SGC200X1000STC Is Used
Automotive Press Transfer
Drives large stamping blanks across a 1000 mm gap with 15708 N of thrust, relying on the TC trunnion to pivot safely under heavy acceleration.
Pallet Dispenser Pusher
Separates stacked pallets in high-throughput logistics lines, utilizing the 801 kg vertical lift equivalent to manage heavy steel or plastic pallet stacks.
Heavy Mold Ejection
Ejects dense industrial molds from casting machines, where the four steel tie rods maintain barrel integrity against 21991 N of push force at 0.7 MPa.
Is the Airtac SGC Standard Cylinder SGC200X1000STC the Right Cylinder?
When sizing this 200 mm bore option, verify your actual load requirements against the adjacent bores: the 160 mm variant yields 10053 N of push at 0.5 MPa, while the 250 mm version steps up to 24543 N. Because this model features a 1000 mm stroke, external guide rails are strongly recommended to prevent rod bending and absorb side loads during long extensions. The TC trunnion mounting accessory provides pivotal support suited for this ISO 15552 interface.
Note that a standard cylinder will drift and cannot hold a vertical load if air pressure drops or the valve is centered; the adjustable cushions only decelerate the piston near the end of travel. To maintain position safely, integrate an external rod lock or a pilot-operated check valve into your pneumatic circuit.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Long-stroke side load — support the rod end
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load; support long strokes at the rod end.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SGC Standard Cylinder SGC200X1000STC FAQ
This 200 mm bore cylinder features a G3/4 air port and generates 15708 N push / 15079 N pull at 0.5 MPa, 21991 N push / 21110 N pull at 0.7 MPa, and a theoretical maximum of 3204 kgf at 1.0 MPa.
No, the double-acting piston will drift if air is exhausted or the valve is centered, as the air cushions only decelerate the piston near stroke ends. You must use an external rod lock or pilot-operated check valve to hold a load safely.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Made to Order
Large-bore cylinders built to order — confirm lead time.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SGC Cylinders
Request a Quote for Airtac SGC Standard Cylinder SGC200X1000STC
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.