Airtac SGC Standard Cylinder SGC200X180S
The AirTAC Airtac SGC Standard Cylinder SGC200X180S is a genuine double acting ISO 15552 (orig. ISO 6431) tie-rod air cylinder with a Ø200mm bore and 180mm stroke, G3/4 air ports and adjustable end cushioning. Its large-bore tie-rod build delivers high thrust and drops into standardized ISO 15552 mounting on heavy automation.
- BoreØ200 mm
- Stroke180 mm
- Port sizeG3/4
- Acting typeDouble acting
- Rod threadM36×2.0
- CushionAdjustable, 50 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SGC Standard Cylinder SGC200X180S
Delivering 15708 N of push force at 0.5 MPa, this large-bore double-acting cylinder is built around a genuine ISO 15552 mounting interface for direct fixture interchangeability. Four steel tie rods clamp the aluminium barrel to the covers, providing the high rigidity needed for heavy thrust, while a two-way piston seal maintains an internal oil reservoir for long service life. Because this SKU includes the -S magnet, it is ready for CMSG, DMSG, or EMSG position switches.
The Ø200 mm bore uses a G3/4 air port and a Ø40 mm hard-chrome rod, yielding a theoretical maximum output of 3204 kgf at 1.0 MPa. For practical sizing, plan for about 9425 N of real work at 0.5 MPa, which equates to lifting roughly 801 kg vertically with a 2:1 safety margin. The standard TPU seals handle -20 to +70 C, though a Viton H option extends this to 0-150 C for hot environments.
Airtac SGC Standard Cylinder SGC200X180S Technical Specifications
| Model | Airtac SGC Standard Cylinder SGC200X180S |
|---|---|
| Series | SGC ISO 15552 tie-rod cylinder |
| Bore size | Ø200 mm |
| Stroke | 180 mm |
| Acting type | Double acting |
| Port size | G3/4 |
| Rod thread | M36×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Adjustable, 50 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC SGC datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Thread options: PT (blank) / G. TPU seals are not available for the Ø250 bore (NBR / Viton only).
Theoretical Output Force (Ø200mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 15708 N | 15080 N |
| 0.7 MPa | 21991 N | — |
| Max (@1.0 MPa) | 3204 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SGC Standard Cylinder SGC200X180S
| SGC | ISO 15552 tie-rod cylinder (double-acting type). |
|---|---|
| 200 | Bore size in mm (125 / 160 / 200 / 250). |
| ×180 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
SGC-family variants: SGC (double acting), SGCD (double rod), SGCJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / FTC / TCM1 / TCM2. Seals: TPU (blank) / Viton H / NBR N.
Where the Airtac SGC Standard Cylinder SGC200X180S Is Used
Heavy-Duty Stamping Press
Generates the 15708 N push force at 0.5 MPa required to drive a large progressive die in an automotive metal-forming line.
Palletiser Head Actuator
Lifts heavy unit loads using the 801 kg vertical lift capacity, while the -S magnet confirms clamp positions via DMSG sensors.
Plastic Injection Mould Ejector
Provides the robust extraction force needed to break large moulded parts free, utilising the rigid four-tie-rod construction.
Is the Airtac SGC Standard Cylinder SGC200X180S the Right Cylinder?
When sizing this 180 mm stroke unit, compare it against its neighbours: the Ø160 bore provides 10053 N of push at 0.5 MPa, while the Ø250 bore steps up to 24543 N. If your application demands holding a load vertically during an air loss or valve centre state, remember that a standard cylinder will drift; the adjustable air cushion only decelerates the piston near stroke end and acts purely as an end-of-stroke buffer, never as a lock. You must add an external rod lock or a pilot-operated check valve for secure load holding.
This model's built-in magnet allows seamless integration of CMSG, DMSG, or EMSG sensors for end-of-stroke confirmation. Although 180 mm is well below the 500 mm side-load threshold, always ensure the rod-end thread (M36x2.0) is correctly aligned with your clevis or knuckle to avoid binding.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Long-stroke side load — support the rod end
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load; support long strokes at the rod end.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SGC Standard Cylinder SGC200X180S FAQ
This Ø200 mm bore cylinder features a G3/4 air port and delivers 15708 N push / 15079 N pull at 0.5 MPa, 21991 N push / 21110 N pull at 0.7 MPa, with a theoretical maximum of 3204 kgf at 1.0 MPa.
Yes, it is dimensionally interchangeable per the ISO 15552 mounting interface, meaning it drops directly into existing large-bore ISO 15552 fixtures, whether you use LB foot mounts, TC trunnions, or CA clevis attachments.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Made to Order
Large-bore cylinders built to order — confirm lead time.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SGC Cylinders
Request a Quote for Airtac SGC Standard Cylinder SGC200X180S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.