Airtac SGC Standard Cylinder SGC200X80SH
The AirTAC Airtac SGC Standard Cylinder SGC200X80SH is a genuine double acting ISO 15552 (orig. ISO 6431) tie-rod air cylinder with a Ø200mm bore and 80mm stroke, G3/4 air ports and adjustable end cushioning. Its large-bore tie-rod build delivers high thrust and drops into standardized ISO 15552 mounting on heavy automation.
- BoreØ200 mm
- Stroke80 mm
- Port sizeG3/4
- Acting typeDouble acting
- Rod threadM36×2.0
- CushionAdjustable, 50 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SGC Standard Cylinder SGC200X80SH
Delivering 15708 N of push force at 0.5 MPa, this double-acting 200 mm bore cylinder is built around a rigid ISO 15552 mounting interface with a 80 mm stroke. Four steel tie rods clamp the aluminum barrel to the covers, ensuring high structural rigidity under heavy thrust, while the two-way piston seal maintains an internal oil reservoir for long mechanical life. Because this SGC200X80SH variant includes the H seal option, it uses Viton FKM elastomers to operate in temperatures up to 150 C, far exceeding the standard 70 C limit.
The integrated -S piston magnet allows direct mounting of CMSG, DMSG, or EMSG electronic switches for position sensing, and the G3/4 port handles high airflow. For practical sizing, plan for about 9425 N of real work at 0.5 MPa, which safely lifts an 801 kg vertical load with a 2:1 margin.
Airtac SGC Standard Cylinder SGC200X80SH Technical Specifications
| Model | Airtac SGC Standard Cylinder SGC200X80SH |
|---|---|
| Series | SGC ISO 15552 tie-rod cylinder |
| Bore size | Ø200 mm |
| Stroke | 80 mm |
| Acting type | Double acting |
| Port size | G3/4 |
| Rod thread | M36×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Adjustable, 50 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC SGC datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Thread options: PT (blank) / G. TPU seals are not available for the Ø250 bore (NBR / Viton only).
Theoretical Output Force (Ø200mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 15708 N | 15080 N |
| 0.7 MPa | 21991 N | — |
| Max (@1.0 MPa) | 3204 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SGC Standard Cylinder SGC200X80SH
| SGC | ISO 15552 tie-rod cylinder (double-acting type). |
|---|---|
| 200 | Bore size in mm (125 / 160 / 200 / 250). |
| ×80 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
SGC-family variants: SGC (double acting), SGCD (double rod), SGCJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / FTC / TCM1 / TCM2. Seals: TPU (blank) / Viton H / NBR N.
Where the Airtac SGC Standard Cylinder SGC200X80SH Is Used
Hot Ingot Pressing
Presses heated metal ingots in a foundry line, utilizing the Viton H seals to withstand 150 C ambient radiant heat while applying 21991 N of push force at 0.7 MPa.
Heavy Stamping Press
Drives a heavy-duty stamping die over an 80 mm travel distance, relying on the four steel tie rods to maintain structural rigidity under 15708 N of dynamic thrust.
Pallet Stopper Gate
Acts as a high-force stopper gate for heavy loaded pallets on a conveyor, using the -S magnet and DMSG switches to confirm gate position in automated logistics.
Is the Airtac SGC Standard Cylinder SGC200X80SH the Right Cylinder?
When sizing this 200 mm bore unit against the SGC family, dropping down to the 160 mm bore reduces thrust to 10053 N at 0.5 MPa, while stepping up to the 250 mm bore increases it to 24543 N. The 80 mm stroke is well within standard limits, so rod-bending side loads are minimal, but always guide the load externally to prevent binding. If the application requires the load to remain suspended when air pressure is lost or the valve is centered, note that the adjustable air cushion only decelerates the piston near the stroke end and does not act as a brake; an external rod lock or pilot-operated check valve is required for holding.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Long-stroke side load — support the rod end
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load; support long strokes at the rod end.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SGC Standard Cylinder SGC200X80SH FAQ
This 200 mm bore cylinder features a G3/4 air port and an M36x2.0 rod thread. It generates 15708 N push and 15079 N pull at 0.5 MPa, 21991 N push and 21110 N pull at 0.7 MPa, with a theoretical maximum force of 3204 kgf at 1.0 MPa.
Yes, it is dimensionally interchangeable per the ISO 15552 mounting interface, so it drops directly into standard large-bore fixtures. The included -S piston magnet enables CMSG, DMSG, and EMSG switches for position sensing, and the H seal option provides Viton FKM components for high-temperature 150 C environments.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Made to Order
Large-bore cylinders built to order — confirm lead time.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SGC Cylinders
Request a Quote for Airtac SGC Standard Cylinder SGC200X80SH
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.