Airtac SGCD Dual Rod Cylinder SGCD200X175S
The AirTAC Airtac SGCD Dual Rod Cylinder SGCD200X175S is a genuine double acting, double rod ISO 15552 (orig. ISO 6431) tie-rod air cylinder with a Ø200mm bore and 175mm stroke, G3/4 air ports and adjustable end cushioning. Its large-bore tie-rod build delivers high thrust and drops into standardized ISO 15552 mounting on heavy automation.
- BoreØ200 mm
- Stroke175 mm
- Port sizeG3/4
- Acting typeDouble acting, double rod
- Rod threadM36×2.0
- CushionAdjustable, 50 mm
About the Airtac SGCD Dual Rod Cylinder SGCD200X175S
Delivering 15079 N of thrust in both directions at 0.5 MPa, this large-bore double-rod cylinder uses a single Ø40 mm piston rod passing through both covers to guarantee identical push and pull forces. The symmetric layout creates a balanced load path that resists torsional twist, while the rear rod extension can drive a secondary mechanism or act as a sensor cam. It offers a safe working load of roughly 9047 N, which translates to lifting about 769 kg vertically with a 2:1 safety factor.
Four steel tie rods clamp the aluminium barrel to the cast covers, and the G3/4 air port feeds the chambers at speeds of 30-500 mm/s. The built-in piston magnet (-S suffix) supports CMSG, DMSG, and EMSG electronic switches for end-of-stroke detection. Because it is dimensionally interchangeable per the ISO 15552 mounting interface, it drops directly into existing large-bore pneumatic fixtures without custom brackets.
Airtac SGCD Dual Rod Cylinder SGCD200X175S Technical Specifications
| Model | Airtac SGCD Dual Rod Cylinder SGCD200X175S |
|---|---|
| Series | SGC ISO 15552 tie-rod cylinder |
| Bore size | Ø200 mm |
| Stroke | 175 mm |
| Acting type | Double acting, double rod |
| Port size | G3/4 |
| Rod thread | M36×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Adjustable, 50 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC SGC datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Thread options: PT (blank) / G. TPU seals are not available for the Ø250 bore (NBR / Viton only).
Theoretical Output Force (Ø200mm)
| Pressure | Force (both ways) | — |
|---|---|---|
| 0.5 MPa | 15080 N | 15080 N |
| 0.7 MPa | 21111 N | 21111 N |
| Max (@1.0 MPa) | 3204 kgf | |
Double-rod: the rod passes through both covers, so output force is equal in both directions.
Model Code: Airtac SGCD Dual Rod Cylinder SGCD200X175S
| SGCD | ISO 15552 tie-rod cylinder (double-rod type). |
|---|---|
| 200 | Bore size in mm (125 / 160 / 200 / 250). |
| ×175 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
SGC-family variants: SGC (double acting), SGCD (double rod), SGCJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / FTC / TCM1 / TCM2. Seals: TPU (blank) / Viton H / NBR N.
Where the Airtac SGCD Dual Rod Cylinder SGCD200X175S Is Used
Twin-Spindle Machining
Drives two opposing machining heads simultaneously using both rod ends, ensuring perfectly synchronized cutting cycles.
Symmetric Transfer Pusher
Pushes a workpiece forward while the rear rod retracts a return conveyor paddle, maintaining a balanced load path.
Guided Vertical Lifter
Lifts heavy pallets with equal force both ways, using the dual rods to prevent rack twist during elevation.
Is the Airtac SGCD Dual Rod Cylinder SGCD200X175S the Right Cylinder?
When sizing this symmetric actuator, step down to the 160 mm bore for 9425 N equal force, or step up to the 250 mm bore for 23562 N if you need heavier lifting. A double-rod design is the right call when you need anti-rotation guidance, twin tooling on one axis, or a back-end position cam. Mounting options include FA, LB, TC, FTC, TCM1, and TCM2 brackets. The -S magnet enables CMSG/DMSG/EMSG sensors. For this 175 mm stroke, ensure external guide rails carry any lateral side-load to prevent premature seal wear.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Long-stroke side load — support the rod end
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load; support long strokes at the rod end.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SGCD Dual Rod Cylinder SGCD200X175S FAQ
It delivers equal force in both directions: 15079 N at 0.5 MPa and 21110 N at 0.7 MPa, with a theoretical maximum of 3075 kgf at 1.0 MPa. The air port size is G3/4.
No, a plain cylinder drifts without live air, and the 50 mm adjustable cushions only decelerate near stroke end. For load holding, install an external rod lock or pilot-operated check valve.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Made to Order
Large-bore cylinders built to order — confirm lead time.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SGC Cylinders
Request a Quote for Airtac SGCD Dual Rod Cylinder SGCD200X175S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.