Airtac SGCJ200-250 Adjustable Cylinder SGCJ250X400-10
The AirTAC Airtac SGCJ200-250 Adjustable Cylinder SGCJ250X400-10 is a genuine double acting, adjustable stroke ISO 15552 (orig. ISO 6431) tie-rod air cylinder with a Ø250mm bore and 400mm stroke, G1 air ports and adjustable end cushioning. Its large-bore tie-rod build delivers high thrust and drops into standardized ISO 15552 mounting on heavy automation.
- BoreØ250 mm
- Stroke400 mm
- Port sizeG1
- Acting typeDouble acting, adjustable stroke
- Rod threadM42×2.0
- CushionAdjustable, 60 mm
About the Airtac SGCJ200-250 Adjustable Cylinder SGCJ250X400-10
Delivering massive thrust, this 250 mm bore tie-rod actuator pushes with 24543 N at 0.5 MPa. It is a genuine ISO 15552 cylinder, dimensionally interchangeable per the standard mounting interface to drop into existing large-bore fixtures. Four steel tie rods clamp the aluminium barrel to the covers, and a two-way piston seal ensures reliable bidirectional control. The G1 air port handles the high volume needed for this bore size.
The -10 code defines a 10 mm external adjuster window, letting you shorten the extend stroke on site from the 400 mm maximum down to 390 mm without changing the cylinder itself. This on-site fine-tuning of the end position is perfect for dialing in a shared spare across slightly different stroke variants. Because this is a 250 bore, TPU seals are not available; standard NBR packing handles the -20 to +70 C range, with a Viton H option for 0-150 C. This SKU lacks a magnet, so it cannot take a magnetic switch without specifying the -S variant for CMSG/DMSG/EMSG sensors.
Airtac SGCJ200-250 Adjustable Cylinder SGCJ250X400-10 Technical Specifications
| Model | Airtac SGCJ200-250 Adjustable Cylinder SGCJ250X400-10 |
|---|---|
| Series | SGC ISO 15552 tie-rod cylinder |
| Bore size | Ø250 mm |
| Stroke | 400 mm |
| Acting type | Double acting, adjustable stroke |
| Port size | G1 |
| Rod thread | M42×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Adjustable, 60 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC SGC datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Thread options: PT (blank) / G. TPU seals are not available for the Ø250 bore (NBR / Viton only).
Theoretical Output Force (Ø250mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 24544 N | 23562 N |
| 0.7 MPa | 34361 N | — |
| Max (@1.0 MPa) | 5006 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SGCJ200-250 Adjustable Cylinder SGCJ250X400-10
| SGCJ | ISO 15552 tie-rod cylinder (adjustable-stroke type). |
|---|---|
| 250 | Bore size in mm (125 / 160 / 200 / 250). |
| ×400 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
SGC-family variants: SGC (double acting), SGCD (double rod), SGCJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / FTC / TCM1 / TCM2. Seals: TPU (blank) / Viton H / NBR N.
Where the Airtac SGCJ200-250 Adjustable Cylinder SGCJ250X400-10 Is Used
Heavy Pallet Lifting
Lifts roughly 1251 kg vertically with a 2:1 safety margin, ideal for raising loaded pallets in automated distribution hubs where the 10 mm stroke adjuster dials in exact upper stops.
Press End Tuning
Provides a safe working load of about 14726 N for assembly presses, using the external adjuster to fine-tune the 390-400 mm extend position without swapping mechanical stops.
Stamping Clamp Adjustment
Clamps heavy steel workpieces in stamping lines, using the G1 port for high flow and the 60 mm adjustable air cushions to decelerate the massive 250 mm piston smoothly.
Is the Airtac SGCJ200-250 Adjustable Cylinder SGCJ250X400-10 the Right Cylinder?
Size this 250 mm bore against the 200 mm option, which provides 15708 N push at 0.5 MPa. If you need more power, this 250 mm model is the top end, yielding 34360 N at 0.7 MPa. The 10 mm adjustable window helps when you need to match end positions precisely on-site or share a spare across 390-400 mm stroke variants. Mounting options include Basic, FA, LB, TC, FTC, TCM1, and TCM2. Since this is a no-S SKU, it cannot accept a magnetic sensor. For any stroke over 500 mm, guide the load externally to prevent side-load wear on the rod and seals.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Long-stroke side load — support the rod end
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load; support long strokes at the rod end.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SGCJ200-250 Adjustable Cylinder SGCJ250X400-10 FAQ
At 0.5 MPa it pushes 24543 N and pulls 23562 N. At 0.7 MPa it pushes 34360 N and pulls 32986 N. The theoretical maximum force is 5006 kgf at 1.0 MPa. It uses a G1 air port and a 50 mm rod with an M42x2.0 thread.
The nominal 400 mm stroke is the maximum. The external adjuster lets you shorten the extend stroke on site by up to 10 mm, giving a usable extend range of 390-400 mm while the retract end remains fixed. This mechanism sets the end position and is not a load lock; a plain cylinder drifts on air loss, so use an external rod lock or pilot-operated check valve to hold a load.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Made to Order
Large-bore cylinders built to order — confirm lead time.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SGC Cylinders
Request a Quote for Airtac SGCJ200-250 Adjustable Cylinder SGCJ250X400-10
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.