Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ25X35S
The AirTAC Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ25X35S is a genuine double-acting GUIDED compact (JIS) cylinder — a Ø25mm bore, 35mm stroke and two guide rods with a fixing plate. The twin guides hold the platform non-rotating to within ±0.15° and carry lateral load a plain compact rod cannot, so it drives and guides a load in one unit.
- BoreØ25 mm
- Stroke35 mm
- Port sizeM5×0.8
- Acting typeDouble acting, guided
- Non-rotating±0.15°
- CushionBumper (both ends)
About the Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ25X35S
The AirTAC TACQ25X35S is a double-acting JIS compact guided cylinder equipped with a 25mm bore and 35mm stroke. It integrates two stainless steel guide rods alongside a fixing plate, ensuring the platform remains non-rotating to a strict ±0.15° tolerance. Because the twin rods carry lateral loads that a plain compact rod cannot, this unit drives and guides your payload simultaneously, effectively replacing a separate linear guide rail.
Drive force equals a standard ACQ of the same bore, as the guides add stiffness rather than thrust. At 0.5 MPa you get 245.4 N of push and 188.9 N of pull, scaling to 343.6 N push at 0.7 MPa, with a maximum push of 50 kgf at 1.0 MPa. The unit features M5x0.8 ports, a fixed TPU elastomer bumper at each end for end-of-stroke deceleration, and an integrated magnet (-S) compatible with reed or solid-state switches.
Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ25X35S Technical Specifications
| Model | Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ25X35S |
|---|---|
| Series | TACQ JIS guided compact cylinder |
| Bore size | Ø25 mm |
| Stroke | 35 mm |
| Acting type | Double acting, guided (non-rotating) |
| Non-rotating tolerance | ±0.15° |
| Port size | M5×0.8 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Max standard stroke | Up to 50 mm |
Specifications follow the official AirTAC TACQ datasheet. Two guide rods carry lateral load and hold rotation to ±0.15°; do not apply reverse torque beyond the datasheet limit. Confirm against the product label before installation.
Theoretical Output Force (Ø25mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 245 N | 189 N |
| 0.7 MPa | 344 N | — |
| Max (@1.0 MPa) | 50 kgf | |
Drive force equals a standard ACQ of the same bore — the guide rods add stiffness, not thrust. Keep moving mass and speed within the datasheet chart (rated at 0.5 MPa).
Model Code: Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ25X35S
| TACQ | JIS compact cylinder WITH guider (non-rotating). |
|---|---|
| 25 | Bore size in mm. |
| ×35 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch sensing (omit = none). |
| thread | Blank = PT; G or NPT available. |
The guide plate replaces a separate rod-thread option. Related: ACQ (plain single rod), ACQD (double rod), ACQJ (adjustable stroke).
Where the Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ25X35S Is Used
Pick-and-Place Head
Drives a small gripper assembly without twisting, keeping component alignment exact during electronic board assembly.
Camera Sensor Slide
Positions a vision system inspection head with ±0.15° non-rotating accuracy for repeatable imaging on a packaging line.
Pallet Stopper Gate
Acts as a rigid stop barrier for lightweight workpieces, absorbing side impacts via the twin guide rods.
Is the Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ25X35S the Right Cylinder?
Selecting this 25mm bore provides 245.4 N push at 0.5 MPa; dropping to a 20mm bore yields 157.1 N, while a 32mm bore offers 402.1 N if your payload requires more thrust. A plain ACQ fits applications needing no lateral load support, and a double-rod ACQD suits higher bending moment demands. Confirm your ordering essentials: 25mm bore, 35mm stroke (within the 50mm maximum), -S magnet, and PT thread. Always verify your lateral load and reverse torque limits against the 0.5 MPa chart, as reverse torque drops with stroke length—confirm the exact value from the datasheet.
Quick checklist
- ✓ Lateral load / non-rotation needed?
- ✓ Moving mass and speed within chart
- ✓ Drive force at your pressure
- ✓ Magnet (S) for sensors?
- ✓ No reverse torque on the guide rods
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Do not apply reverse torque above the datasheet limit.
- check Apply external force concentric with the rod.
- check Keep mass × speed within the performance chart.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ25X35S FAQ
This double-acting cylinder provides 245.4 N push and 188.9 N pull at 0.5 MPa, 343.6 N push at 0.7 MPa, and a maximum push of 50 kgf at 1.0 MPa. The stroke is 35mm (maximum standard stroke for this bore is 50mm). Twin guide rods ensure a non-rotating tolerance of ±0.15°.
The two stainless steel guide rods absorb lateral loads that a plain compact rod cannot. A maximum allowable reverse torque exists and decreases as stroke length increases—cite this only as an order-of-magnitude and confirm the exact figure from the datasheet. Never apply reverse torque above this limit, and apply external force concentric with the rod.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC TACQ Guided Cylinders
Request a Quote for Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ25X35S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.