Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ32X75
The AirTAC Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ32X75 is a genuine double-acting GUIDED compact (JIS) cylinder — a Ø32mm bore, 75mm stroke and two guide rods with a fixing plate. The twin guides hold the platform non-rotating to within ±0.15° and carry lateral load a plain compact rod cannot, so it drives and guides a load in one unit.
- BoreØ32 mm
- Stroke75 mm
- Port sizePT1/8
- Acting typeDouble acting, guided
- Non-rotating±0.15°
- CushionBumper (both ends)
About the Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ32X75
The AirTAC TACQ32X75 is a double-acting JIS compact guided cylinder featuring a 32mm bore and 75mm stroke. Two stainless steel guide rods and a fixing plate work together to carry lateral loads and prevent platform rotation. This unit holds a non-rotating tolerance of ±0.15° at the retracted position, successfully replacing a separate linear guide by driving and guiding a load in one block.
Drive output matches a standard ACQ of the same bore, because the twin shafts add structural stiffness rather than thrust. The unit pushes with 402.1N and pulls with 301.6N at 0.5MPa, reaching 562.9N at 0.7MPa. It relies on a fixed NBR elastomer bumper at each end for end-of-stroke deceleration rather than an adjustable air cushion. The body includes magnetic-switch grooves, though this specific configuration ships without a magnet. You must keep any applied external force concentric with the rod and never exceed the maximum allowable reverse torque.
Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ32X75 Technical Specifications
| Model | Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ32X75 |
|---|---|
| Series | TACQ JIS guided compact cylinder |
| Bore size | Ø32 mm |
| Stroke | 75 mm |
| Acting type | Double acting, guided (non-rotating) |
| Non-rotating tolerance | ±0.15° |
| Port size | PT1/8 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC TACQ datasheet. Two guide rods carry lateral load and hold rotation to ±0.15°; do not apply reverse torque beyond the datasheet limit. Confirm against the product label before installation.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 302 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Drive force equals a standard ACQ of the same bore — the guide rods add stiffness, not thrust. Keep moving mass and speed within the datasheet chart (rated at 0.5 MPa).
Model Code: Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ32X75
| TACQ | JIS compact cylinder WITH guider (non-rotating). |
|---|---|
| 32 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch sensing (omit = none). |
| thread | Blank = PT; G or NPT available. |
The guide plate replaces a separate rod-thread option. Related: ACQ (plain single rod), ACQD (double rod), ACQJ (adjustable stroke).
Where the Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ32X75 Is Used
Pick-and-Place Head
Drives a small gripper on an electronics assembly line, using the twin guide rods to resist jaw swing and maintain precise vertical placement.
PCB Pressing Fixture
Applies 402.1N of downward force to seat connectors on a circuit board, relying on the ±0.15° non-rotating accuracy to prevent component skewing.
Pallet Stopper Gate
Acts as a height barrier on a packaging conveyor, absorbing side impacts from passing product carriers without bending a plain piston rod.
Is the Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ32X75 the Right Cylinder?
For sizing context: dropping down to a 25mm bore yields 245.4N push, while stepping up to a 40mm bore provides 628.3N push at 0.5MPa. Choose this 32mm bore if your required force sits comfortably above 245.4N but below 628.3N. A plain ACQ fits tighter spaces if lateral loads are absent, and a double-rod ACQD works better for higher opposing moments. When ordering, confirm the 75mm stroke is within the 100mm maximum, specify PT1/8 ports, and verify the mass and speed limits charted at 0.5MPa. Always confirm the exact reverse torque limit for this 75mm stroke from the datasheet, as it decreases with extended length.
Quick checklist
- ✓ Lateral load / non-rotation needed?
- ✓ Moving mass and speed within chart
- ✓ Drive force at your pressure
- ✓ Magnet (S) for sensors?
- ✓ No reverse torque on the guide rods
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Do not apply reverse torque above the datasheet limit.
- check Apply external force concentric with the rod.
- check Keep mass × speed within the performance chart.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ32X75 FAQ
This double-acting 32mm bore cylinder pushes with 402.1N and pulls with 301.6N at 0.5MPa, reaching 562.9N at 0.7MPa, with a maximum push of 82kgf at 1.0MPa. The piston rod is 16mm, the port is PT1/8, and the female rod-end thread is M8x1.25. The twin guide rods hold a non-rotating tolerance of ±0.15°, and the maximum standard stroke for this bore is 100mm.
The two stainless steel guide rods provide lateral-load support but have a maximum allowable reverse torque that decreases as stroke length increases. For this 75mm unit, treat the torque limit as an order-of-magnitude figure and confirm the exact value from the datasheet. End cushioning relies on a fixed NBR elastomer bumper, not an adjustable air cushion, so add an external shock absorber for high-energy loads.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC TACQ Guided Cylinders
Request a Quote for Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ32X75
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.