Airtac ACE Compact Cylinder ACE32X10SH
The AirTAC Airtac ACE Compact Cylinder ACE32X10SH is a genuine double acting ISO 21287 compact air cylinder with a Ø32mm bore and 10mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
- BoreØ32 mm
- Stroke10 mm
- Port size1/8"
- Acting typeDouble acting
- Rod threadM8×1.25
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACE Compact Cylinder ACE32X10SH
This AirTAC ACE32X10SH is a double acting ISO 21287 compact cylinder with a 32 mm bore and a 10 mm stroke, delivering 402.1 N of push force at 0.5 MPa. Its short body takes up about 50% less mounting length than an ISO 15552 profile cylinder, so it fits into tight machine frames and guarding where a full-length unit would not.
The optional -S magnet is already fitted on this model, letting you mount CMSE or DMSE reed or solid-state switches for end-of-stroke sensing. For a safe working load, plan for roughly 241 N (about 24.6 kg) of real work at 0.5 MPa, not the full rating, to account for friction and dynamic loads. The fixed TPU bumper at both ends absorbs end-of-stroke impact, but it does not hold a load in place if air pressure is lost.
Airtac ACE Compact Cylinder ACE32X10SH Technical Specifications
| Model | Airtac ACE Compact Cylinder ACE32X10SH |
|---|---|
| Series | ACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø32 mm |
| Stroke | 10 mm |
| Acting type | Double acting |
| Port size | 1/8" |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 200 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | 484 N |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac ACE Compact Cylinder ACE32X10SH
| ACE | ISO 21287 compact cylinder (double-acting). |
|---|---|
| 32 | Bore size in mm. |
| ×10 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac ACE Compact Cylinder ACE32X10SH Is Used
Tight Jig Clamping
Use in a CNC fixture to clamp small parts with a 10 mm stroke, where the short body fits under a workholding plate and the 402.1 N push force holds components firmly during milling.
Label Applicator Press
Mount on a packaging line to press labels onto cartons with a quick 10 mm stroke. The compact size fits between conveyor rails, and the magnet lets a CMSE switch confirm each press cycle.
Guard Door Stop
Act as a stop pin on a machine safety guard, extending 10 mm to block a sliding door. The 345.6 N pull force retracts the pin reliably, and the fixed TPU bumper prevents noise at high cycle rates.
Is the Airtac ACE Compact Cylinder ACE32X10SH the Right Cylinder?
For a lighter duty, the ACE25X10 offers 245.4 N push at 0.5 MPa, while stepping up to the ACE40X10 gives you 628.3 N push at the same pressure. If your application needs to hold a vertical load when air is off, add a rod lock or pilot check valve because this cylinder drifts without air pressure. The 1/8" port and M8x1.25 female rod thread suit standard fittings, and the compact body accepts FA, FB, LB, CA, CB, CR, SDB, and FTC mounting brackets.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac ACE Compact Cylinder ACE32X10SH FAQ
At 0.5 MPa, the push force is 402.1 N and the pull force is 345.6 N. At 0.7 MPa, push is 563 N and pull is 483.8 N. The theoretical maximum force is 82 kgf at 1.0 MPa. Operating pressure range is 0.15-1.0 MPa (22-145 psi), with a proof pressure of 1.5 MPa (215 psi).
The ACE32X10SH body is about 50% shorter than an ISO 15552 profile cylinder, so it saves valuable mounting space in tight fixtures. It has a hard-anodized aluminium body and a fixed TPU bumper at both ends, which absorbs impact but does not lock the rod. The optional -S magnet is fitted here for CMSE or DMSE sensors, and the 1/8" port accepts standard fittings.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac ACE Compact Cylinder ACE32X10SH
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.