Every AirTAC SC63 configuration on one page: 20 stock order codes with strokes from 25 to 940 mm, 2 mounting styles and 2 magnet, seal and thread versions, from $135.78. Pick a stroke, mounting and version to see the exact order code and price.
This combination is not a stock order code. Request a quote and we will confirm availability and price.
The AirTAC SC63 is a double-acting tie-rod cylinder with a 63 mm bore and a 20 mm piston rod. At 0.5 MPa it pushes 1559 N and pulls 1402 N; at 0.7 MPa that rises to 2182 N push and 1962 N pull. Force depends on bore and pressure only, so every stroke on this page gives the same output.
All SC63 versions share PT1/4 air ports, an M16×1.5 rod thread and 28 mm adjustable air cushions at both ends. The cylinder runs on filtered air between 0.15 and 1.0 MPa, from -20 to +70 °C, at 30 to 800 mm/s. This page lists 20 stock order codes with strokes from 25 to 940 mm; catalog standard strokes run up to 1500 mm.
| Bore size | Ø63 mm |
|---|---|
| Stock strokes | 25 – 940 mm |
| Catalog standard stroke | up to 1500 mm (longer on request) |
| Acting type | Double acting |
| Port size | PT1/4 (G on request) |
| Piston rod / rod thread | Ø20 mm / M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 28 mm |
Source: AirTAC Products Catalog 2026A, SC series pages. Standard seal is TPU; H = FKM, N = NBR. Thread: blank = PT, G = G thread.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | 1962 N |
Push = pressure × bore area; pull subtracts the Ø20 mm rod area. Force does not depend on stroke. Usable force is lower because of friction and back-pressure.
| SC63 | Series and bore (mm) |
|---|---|
| X100 | Stroke in mm |
| S | Built-in magnet for position sensors (blank = none) |
| LB / FA / FB / CA / CB / TC | Foot, front flange, rear flange, single clevis, double clevis, center trunnion (blank = basic) |
| H / N | FKM or NBR seals (blank = TPU) |
| G | G port thread (blank = PT) |
Example: SC63X100SCA = Ø63 mm bore, 100 mm stroke, magnet, single clevis mounting.
Each order code links to its own datasheet page. Use Select to load it into the configurator above.
| Order code | Stroke (mm) | Mounting | Magnet · Seal · Thread | Price | Select |
|---|---|---|---|---|---|
| SC63X25 | 25 | - | - · TPU · PT | $135.78 | |
| SC63X25CB | 25 | CB | - · TPU · PT | $154.08 | |
| SC63X75S | 75 | - | S · TPU · PT | $161.31 | |
| SC63X75 | 75 | - | - · TPU · PT | $153.53 | |
| SC63X80S | 80 | - | S · TPU · PT | $163.08 | |
| SC63X80 | 80 | - | - · TPU · PT | $155.31 | |
| SC63X100 | 100 | - | - · TPU · PT | $162.35 | |
| SC63X125S | 125 | - | S · TPU · PT | $179.10 | |
| SC63X125 | 125 | - | - · TPU · PT | $171.17 | |
| SC63X150S | 150 | - | S · TPU · PT | $187.88 | |
| SC63X175 | 175 | - | - · TPU · PT | $188.92 | |
| SC63X200S | 200 | - | S · TPU · PT | $205.67 | |
| SC63X200 | 200 | - | - · TPU · PT | $197.73 | |
| SC63X500S | 500 | - | S · TPU · PT | $311.97 | |
| SC63X600 | 600 | - | - · TPU · PT | $339.59 | |
| SC63X650S | 650 | - | S · TPU · PT | $365.11 | |
| SC63X660S | 660 | - | S · TPU · PT | $368.66 | |
| SC63X800 | 800 | - | - · TPU · PT | $410.48 | |
| SC63X900 | 900 | - | - · TPU · PT | $445.87 | |
| SC63X940S | 940 | - | S · TPU · PT | $467.90 |
Mounting: - = basic, LB = foot, FA = front flange, FB = rear flange, CA = single clevis, CB = double clevis, TC = center trunnion. Magnet: S = with magnet, - = without. Need a stroke or combination that is not listed? Request a quote.
About 1559 N at 0.5 MPa covers most pushing, lifting and indexing tasks on production machinery.
Foot or flange mounting holds the cylinder rigid for workholding clamps and hold-downs.
Clevis and trunnion versions drive mechanisms that swing through an arc as the rod extends.
Start with the stroke. Pick the exact travel your machine needs; a longer stroke than necessary adds length, weight and air consumption without adding force. If your length is not listed, request a quote and we will confirm whether it can be built.
Then choose the mounting. Basic (no code) has threaded end-cover holes for your own bracket. This bore is stocked with CB double clevis. Foot and flange mountings fix the cylinder rigidly for straight-line motion; clevis and trunnion mountings let it pivot when the load moves in an arc.
Finally pick the version. Add the magnet (S) if you will fit position sensors on the tie rods. The standard TPU seal suits general automation.
No. Output force depends on bore and air pressure. Every SC63 gives about 1559 N push and 1402 N pull at 0.5 MPa, whatever the stroke.
PT1/4 as standard.
Basic plus CB double clevis. Use foot or flange for straight-line loads, clevis or trunnion when the cylinder must pivot.
Blank means the standard TPU seal. H is FKM, for higher temperatures or oil in the air.
Usually yes. Request a quote with the stroke, mounting and version and we will confirm whether it can be built, plus price and lead time.
No. You can order a single SC63. Orders are processed and handed to the carrier within 3-5 business days.
Every order code on this page is the AirTAC factory part number. Specifications follow the AirTAC Products Catalog 2026A. About us
That is our time to process the order and hand it to the carrier. No minimum order: a single cylinder can be ordered.
Return within 14 days of delivery; the buyer pays return shipping. The warranty covers defects not caused by misuse. Return policy
Send your load, stroke and mounting and we will confirm the right order code, usually within 7-8 hours. Ask us
Page data checked against the live catalog on 2026-09-27.
Send the order code, quantity and destination. We confirm price, stock and lead time, usually within 7-8 hours.