Airtac ACED Double-acting Compact Cylinder ACED100X200S
The AirTAC Airtac ACED Double-acting Compact Cylinder ACED100X200S is a genuine double acting, double rod ISO 21287 compact air cylinder with a Ø100mm bore and 200mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
- BoreØ100 mm
- Stroke200 mm
- Port size1/4"
- Acting typeDouble acting, double rod
- Rod threadM12×1.75
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACED Double-acting Compact Cylinder ACED100X200S
A double acting compact cylinder built to ISO 21287, the ACED100X200S pushes a 100 mm bore through a 200 mm stroke with a rod leaving BOTH covers, so thrust is identical on every stroke: 3769.9 N at 0.5 MPa and 5277.9 N at 0.7 MPa. Air supply is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), and speed runs 30-500 mm/s.
The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which matters on wide press platens and gantry lifters where depth is scarce. The through-rod resists rotation and side load and gives a symmetric mount, and the rear rod can carry a sensor flag. This S-code unit carries the optional -S magnet, so CMSE / DMSE switches mount along the body slots. A fixed TPU bumper sits at each end, and the hard-anodized aluminium body with S45C hard-chrome rod shrugs off wear. At 0.5 MPa the rod-side force equals roughly 384 kgf, so halving for a 2:1 margin it lifts about 192 kg vertically.
Airtac ACED Double-acting Compact Cylinder ACED100X200S Technical Specifications
| Model | Airtac ACED Double-acting Compact Cylinder ACED100X200S |
|---|---|
| Series | ACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø100 mm |
| Stroke | 200 mm |
| Acting type | Double acting, double rod |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø100mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 3770 N |
| 0.7 MPa | 5278 N |
| Max (@1.0 MPa) | 769 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACED Double-acting Compact Cylinder ACED100X200S
| ACED | ISO 21287 compact cylinder (double-rod). |
|---|---|
| 100 | Bore size in mm. |
| ×200 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac ACED Double-acting Compact Cylinder ACED100X200S Is Used
Pallet stacker lift plates
The equal 3769.9 N in both directions lowers and raises a stacker plate smoothly, and with the -S magnet fitted a DMSE switch confirms top-of-stack position on each 200 mm cycle.
Press platen return
A rod on both covers lets the rear rod drive a return link on a small stamping platen, so one cylinder does the work of two and the short body fits the shallow press frame.
Clamp fixture counter-balance
Mounted FA flange on a machining fixture, the through-rod carries a counter-weight bracket and resists the side load of an off-centre aluminium casting clamp.
Is the Airtac ACED Double-acting Compact Cylinder ACED100X200S the Right Cylinder?
At 3769.9 N per direction this bore 100 unit sits far above the 50 mm class (881.2 N) and below the 125 mm class (5890.5 N); step down or up only if your load sits between those figures. Remember the piston drifts if air is lost - for a held load add a rod lock or pilot check. The 200 mm stroke is within the 300 mm standard limit for bore 100, and FA/FB flange or LB foot brackets bolt straight to the ISO 21287 face.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac ACED Double-acting Compact Cylinder ACED100X200S FAQ
Because a rod exits both covers, output is equal both ways: 3769.9 N at 0.5 MPa and 5277.9 N at 0.7 MPa, with a peak of 768.8 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi), proof 1.5 MPa (215 psi), speed 30-500 mm/s, temperature -20 to +70 C, air filtered to 40 um.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it fits shallow gantries and guarded cells. This model carries the optional -S magnet, so CMSE / DMSE reed or solid-state switches read position along the body slots; the fixed TPU bumpers decelerate at each end of the 200 mm stroke.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac ACED Double-acting Compact Cylinder ACED100X200S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.