Airtac ACED Double-acting Compact Cylinder ACED80X90B
The AirTAC Airtac ACED Double-acting Compact Cylinder ACED80X90B is a genuine double acting, double rod ISO 21287 compact air cylinder with a Ø80mm bore and 90mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
- BoreØ80 mm
- Stroke90 mm
- Port size1/4"
- Acting typeDouble acting, double rod
- Rod threadM12×1.75
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACED Double-acting Compact Cylinder ACED80X90B
A double acting compact cylinder built to ISO 21287, the ACED80X90B pushes a 20 mm rod out of BOTH covers, so thrust is identical on the extend and retract strokes. At 0.5 MPa the 80 mm bore delivers 2356.2 N in either direction, rising to 3298.7 N at 0.7 MPa. The B code gives a male rod thread on each end, ready for knuckles or tooling plates.
The short hard-anodized aluminium body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which is why it slots into presses and gantries where a full-length body will not fit. The through-rod resists rotation and side load, and the rear rod can carry a sensor flag. Plan on roughly 1414 N of real work at 0.5 MPa (about 0.6 of the rating), which lifts about 72 kg vertically with a 2:1 margin. A fixed TPU bumper at each end absorbs end-of-stroke shock; speed range is 30-500 mm/s.
Airtac ACED Double-acting Compact Cylinder ACED80X90B Technical Specifications
| Model | Airtac ACED Double-acting Compact Cylinder ACED80X90B |
|---|---|
| Series | ACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø80 mm |
| Stroke | 90 mm |
| Acting type | Double acting, double rod |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø80mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 2356 N |
| 0.7 MPa | 3299 N |
| Max (@1.0 MPa) | 481 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACED Double-acting Compact Cylinder ACED80X90B
| ACED | ISO 21287 compact cylinder (double-rod). |
|---|---|
| 80 | Bore size in mm. |
| ×90 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac ACED Double-acting Compact Cylinder ACED80X90B Is Used
Punch press staging
The 2356.2 N symmetric thrust seats aluminium brackets into a locating nest, and the 90 mm stroke clears the operator's hands between cycles.
Push-pull fixture clamping
A rod on each cover lets one cylinder clamp from both sides of a welding jig, halving valve count on the fixture plate.
Gantry part lower-and-release
The rear rod carries a position flag while the front rod lowers about 72 kg castings onto a conveyor, with the TPU bumper softening the touchdown.
Is the Airtac ACED Double-acting Compact Cylinder ACED80X90B the Right Cylinder?
Size up or down by force: the 63 mm double-rod bore gives 1458.1 N at 0.5 MPa, while the 100 mm bore reaches 3769.9 N. This 80 mm model sits between them at 2356.2 N both ways. Stroke 90 mm is well inside the 300 mm standard limit for this bore, so no made-to-order build is needed. Ports are 1/4" PT. If the load must stay put when air is lost, add a rod lock or pilot check - this cylinder drifts. FA/FB flanges, LB feet and FTC brackets bolt to the ISO 21287 face; I and Y rod knuckles suit the male threaded rod. There is no magnet on this code - order ACED80X90BS if you need CMSE / DMSE switching.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac ACED Double-acting Compact Cylinder ACED80X90B FAQ
Yes - the double-rod design means both strokes use the rod-side area, so output is equal either way: 2356.2 N at 0.5 MPa and 3298.7 N at 0.7 MPa, with a peak of 480.5 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, and the 90 mm stroke sits within the 300 mm standard stroke for the 80 mm bore.
It is a short ISO 21287 compact body in hard-anodized aluminium with an S45C hard-chrome plated 20 mm rod and a fixed TPU bumper at each end - about 50% shorter in mounting length than an ISO 15552 profile cylinder. This ACED80X90B code has no magnet; order the -S variant (ACED80X90BS) to enable CMSE or DMSE switches. FA/FB flange, LB foot and FTC mountings bolt straight to the standard face.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac ACED Double-acting Compact Cylinder ACED80X90B
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.