Airtac GAFC Air Service Unit GAFC20006SW
The AirTAC Airtac GAFC Air Service Unit GAFC20006SW is a genuine two-piece F.R.L. combination — a GA-series filter & regulator and a lubricator pre-assembled on one T-shape bracket with quick mounting clamps. It has 1/8" ports, a 5 µm filter element and regulates 0.15 - 0.9 MPa (20 - 130 psi).
- TypeF.R.L. combination
- Port size1/8"
- Pressure range0.15 - 0.9 MPa (20 - 130 psi)
- Filtering grade5 µm
- Bowl materialPC
- Drainsemi-auto + manual
- Pressure gaugeCircular, MPa / psi
- Weight590 g
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac GAFC Air Service Unit GAFC20006SW
This GAFC20006SW is an F.R.L. combination that pairs a filter-regulator with a lubricator on a single T-bracket. The 1/8in port size and 590 g mass place it in the smallest GAFC class, suited to a single actuator or a small jig. Air enters the first body where the 5 um element traps fine particles and the regulator sets pressure to 0.15-0.9 MPa (20-130 psi); the lubricator then adds a metered oil mist downstream.
The 25 cc condensate bowl and 36 cc oil bowl are the service interval drivers, so a compact machine with light duty cycles will need more frequent attention than a larger unit. The circular gauge reads MPa and psi on the default PT thread. With a 1.0 MPa (145 psi) maximum supply, there is about 0.1 MPa of headroom above the 0.9 MPa top of the regulated band, so plan the inlet pressure carefully if you intend to run near the upper limit.
Airtac GAFC Air Service Unit GAFC20006SW Technical Specifications
| Model | Airtac GAFC Air Service Unit GAFC20006SW |
|---|---|
| Series | GAFC200 F.R.L. combination |
| Port size | 1/8" (PT thread) |
| Filtering grade | 5 µm |
| Pressure range | 0.15 - 0.9 MPa (20 - 130 psi) |
| Type | Standard |
| Bowl material | PC |
| Drain type | Semi-auto drain + manual drain |
| Fluid | Air |
|---|---|
| Max. pressure | 1.0 MPa (145 psi) |
| Proof pressure | 1.5 MPa (215 psi) |
| Temperature range | -5 to +70 °C (unfreeze) |
| Capacity of drain bowl | 25 cc |
| Capacity of oil bowl | 36 cc |
| Recommended lubricant | ISO VG 32 or equivalent |
| Weight | 590 g |
Specifications follow the official AirTAC GAFC catalogue (pages 219-220). Air must not freeze in the unit. The fitted circular gauge reads in MPa / psi, set by the PT thread code.
Model Code: Airtac GAFC Air Service Unit GAFC20006SW
| GAFC200 | GA200 series F.R.L. unit — sets ports, bowl capacity and weight. |
|---|---|
| (blank) | Bowl material: PC. Available on this body: PC (blank), Metal (C), Nylon (N). |
| 06 | Port size 1/8". This body offers 06 = 1/8", 08 = 1/4". |
| (blank) | Drain: Semi-auto drain + manual drain. |
| S | Standard type — 0.15 - 0.9 MPa (20 - 130 psi). This body offers Standard (S) or Lower pressure (L). |
| (blank) | Circular pressure gauge fitted. |
| W | Filtering grade 5 µm. |
| (blank) | PT thread; gauge scale MPa / psi. |
| (blank) | No reverse-flow valve. |
Constituent units, orderable separately as spares: GAFR200-06 filter & regulator, GAL200-06 lubricator — both share this body and port. A GAFC has two units, not three: the filter and the regulator are one body.
Size Class & Flow Envelope
- GAFC2001/8"-1/4" · 1750 L/min
- GAFC3001/4"-1/2" · 3500 L/min
- GAFC4003/8"-1/2" · 6000 L/min
- GAFC5003/4" · 7000 L/min
- GAFC6003/4"-1" · 12000 L/min
Figures are the end of the flow curve plotted in the AirTAC catalogue at 0.7 MPa inlet pressure — a sizing envelope for comparing bodies, not a rated flow. Read the catalogue curve for a real duty point. Outlet pressure falls as flow rises, so size a body with headroom above your peak demand.
| This model | GAFC200 · 1/8" · curve to 1750 L/min |
|---|---|
| One size up | GAFC300 (curve to 3500 L/min) |
| Build order | Filter & regulator → bracket → lubricator |
Where the Airtac GAFC Air Service Unit GAFC20006SW Is Used
Precision Jig Fixture
Feed a single pneumatic clamp on a benchtop assembly jig with clean, regulated air. The 5 um element protects the clamp's pilot valve from fine abrasive particles that would otherwise cause premature wear.
Laboratory Air Supply
Supply a small lab instrument that needs oil-misted air for actuation. The compact 1/8in port and 590 g mass fit neatly into a crowded bench setup without requiring heavy structural support.
Single-Actuator Paint Line
Operate one small paint-spray trigger cylinder on a short production line. The semi-auto drain clears condensate each time the line stops, and the 36 cc oil bowl keeps the actuator lubricated through a full shift.
Is the Airtac GAFC Air Service Unit GAFC20006SW the Right Air-Prep Unit?
Choose the GAFC200 body when your air prep point serves one small cylinder, a compact valve manifold, or a bench fixture. The 1/8in port matches short, low-flow runs; step up to the GAFC300 if you need more capacity, as its catalogue flow curve is plotted to 3500 L/min at 0.7 MPa inlet versus 1750 L/min here. The PC bowl is the standard build, and the shared specification of 1.0 MPa max and -5 to 70 C applies regardless of material, so confirm the plastic suits your environment. The 5 um element gives finer filtration than the standard 40 um grade, which protects precision valves but will load faster and need more frequent replacement. Both a semi-auto drain (dumps on pressure drop) and a manual drain are fitted, giving you a choice between automatic purging and on-demand operation. The circular gauge is supplied and reads MPa/psi. Spare parts are orderable as GAFR200-06 and GAL200-06, so a clogged element does not force a whole new assembly. The 1.0 MPa max supply sits just 0.1 MPa above the 0.9 MPa top of the regulated band, so keep inlet pressure near maximum if you need the full output range.
Quick checklist
- ✓ Body size for your peak flow (1/8" here)
- ✓ Standard 0.9 MPa or lower-pressure 0.4 MPa
- ✓ Bowl material: PC (blank), Metal (C), Nylon (N)
- ✓ Drain: semi-auto + manual, or automatic
- ✓ Element 40 µm or 5 µm
- ✓ Thread & gauge scale (PT / G / NPT)
Installation & Maintenance Notes
- check Install with the airflow arrow: filter-regulator first, lubricator last.
- check Keep inlet pressure at or below 1.0 MPa (145 psi).
- check Fill the oil bowl with ISO VG 32 or equivalent only.
- check Drain condensate before the 25 cc bowl fills.
- check Keep the unit above freezing (-5 to +70 °C, unfreeze).
- check Support the 590 g unit on its bracket, not on the tubing.
The lubricator adds an oil mist downstream of the regulator. If any part of the line must stay oil-free, use a plain GAFR200-06 filter-regulator on that branch instead of the full combination.
Airtac GAFC Air Service Unit GAFC20006SW FAQ
The GAFC20006SW operates on air with a standard pressure range of 0.15-0.9 MPa (20-130 psi). Maximum supply pressure is 1.0 MPa (145 psi) and proof pressure is 1.5 MPa (215 psi). The temperature range is -5 to 70 C and it must not freeze. It has a 25 cc drain bowl and a 36 cc oil bowl, weighs 590 g, and uses ISO VG 32 or equivalent lubricant. The 5 um element is fitted.
The W code specifies a 5 um element for finer filtration. This traps smaller particles that could score precision spool valves or instrument orifices. The trade-off is that the element loads faster, so it will need more frequent inspection and replacement than a 40 um element in the same service.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC Air-Preparation Units
Request a Quote for Airtac GAFC Air Service Unit GAFC20006SW
Send us the quantity, thread type (PT / G / NPT) and destination. We confirm price, stock and lead time — usually within 7-8 hours.