Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X110-20
The AirTAC Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X110-20 is a genuine double-acting COMPACT cylinder (Ø100mm bore) whose extend end-position is set by an external M27×2.0 adjustment screw. You can dial the stroke anywhere from 90 to 110 mm on the machine — no shims, no part change.
- BoreØ100 mm
- Max stroke110 mm
- Adjustable range90–110 mm
- Adjuster threadM27×2.0
- Port sizePT3/8
- CushionFixed NBR bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X110-20
The AirTAC SDAJ100X110-20 is a double-acting compact cylinder featuring an external adjustable extend stop. By turning the R (M27x2.0) screw, you shorten the forward stroke on-site across a 90 to 110 mm window without changing parts or shims. Delivering 3927 N of push force at 0.5 MPa, the stop sets the end position without altering the pneumatic area.
Its short riveted body drastically reduces axial mounting depth compared to conventional round-body alternatives, fitting into tight machine frames. End-of-travel shock is handled by a fixed NBR bumper rather than an adjustable air cushion. Note that this specific SKU lacks a piston magnet, so it cannot host reed or electronic switches.
Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X110-20 Technical Specifications
| Model | Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X110-20 |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø100 mm |
| Max stroke | 110 mm |
| Adjustable range | 90 – 110 mm |
| Adjuster thread (R) | M27×2.0 |
| Port size | PT3/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M18×1.5 F / M26×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 20 mm. Force is unchanged from a standard SDA of the same bore. Specifications follow the official AirTAC SDAJ datasheet.
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3525 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Force matches a standard SDA of the same bore; the adjuster only sets the stop position, not the area. Actual usable force is lower than theoretical due to friction.
Model Code: Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X110-20
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 100 | Bore size in mm. |
| ×110 | Maximum stroke length in mm. |
| -20 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Where the Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X110-20 Is Used
Heavy Press Positioning
Dial in the 90-110 mm extend stop during press setup to apply precise 3927 N clamping force without re-engineering tooling heights.
Vertical Lift Stops
Lift loads up to 200.2 kg with a 2:1 margin, tweaking the mechanical stop to set exact drop depths across varying product stacks.
Compact Assembly Cells
Utilize the short riveted body to save axial depth in dense automated cells while handling high-energy end stops via the fixed NBR bumper.
Is the Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X110-20 the Right Cylinder?
When sizing this actuator, evaluate your force requirements bidirectionally. Stepping down to an SDAJ80 yields 2513.3 N of push at 0.5 MPa, whereas this 100 mm bore provides 3927 N. A safe working load is approximately 2356 N, representing about 60 percent of the 0.5 MPa push figure, which allows a vertical lift of roughly 200.2 kg with a 2:1 safety margin.
Operators needing on-site stroke tuning for frequent changeovers will benefit from the 20 mm adjustment window. Remember that a standard cylinder drifts when air is lost or the valve centers; the bumper and mechanical stop decelerate the piston but do not lock the load. For suspended loads, install an external rod lock or pilot-operated check valve. This model uses a PT3/8 port, a 32 mm rod, and a female M18x1.5 rod-end thread, with no magnet included.
Quick checklist
- ✓ Need on-machine stroke fine-tuning?
- ✓ Target position within 90–110 mm
- ✓ Force at your working pressure
- ✓ Access to reach the R adjuster
- ✓ Magnet (S) for sensors?
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Lock the M27×2.0 adjuster after setting the stroke.
- check Avoid side load on the piston rod.
- check Front/rear covers are riveted — do not dismantle.
- check Installation by qualified personnel per AirTAC docs.
Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X110-20 FAQ
At 0.5 MPa this 100 mm bore cylinder provides 3927 N push and 3524.9 N pull. At 0.7 MPa it provides 5497.8 N push and 4934.8 N pull. The theoretical maximum push is 801 kgf at 1.0 MPa.
The M27x2.0 adjuster screw mechanically limits the extend stroke, allowing you to set the end position anywhere between 90 and 110 mm. It acts purely as a stop and does not alter the force or lock the piston mid-stroke.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SDAJ Cylinders
Request a Quote for Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X110-20
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.