Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X60-50S
The AirTAC Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X60-50S is a genuine double-acting COMPACT cylinder (Ø100mm bore) whose extend end-position is set by an external M27×2.0 adjustment screw. You can dial the stroke anywhere from 10 to 60 mm on the machine — no shims, no part change.
- BoreØ100 mm
- Max stroke60 mm
- Adjustable range10–60 mm
- Adjuster threadM27×2.0
- Port sizePT3/8
- CushionFixed NBR bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X60-50S
The AirTAC SDAJ100X60-50S is a compact double-acting single-rod cylinder featuring an external adjustable extend stop. By turning the R (M27x2.0) screw, you can dial the extend position anywhere between 10 and 60 mm directly on the machine without changing parts. The adjuster sets the mechanical stop, so force remains identical to a standard SDA of this bore, delivering 3927 N push at 0.5 MPa.
Its short riveted body drastically saves axial mounting depth where larger profile cylinders cannot fit. End-of-stroke deceleration is handled by a fixed NBR bumper rather than an adjustable air cushion. Equipped with a built-in magnet (-S), it supports AirTAC reed or electronic switches for position sensing.
Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X60-50S Technical Specifications
| Model | Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X60-50S |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø100 mm |
| Max stroke | 60 mm |
| Adjustable range | 10 – 60 mm |
| Adjuster thread (R) | M27×2.0 |
| Port size | PT3/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M18×1.5 F / M26×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 50 mm. Force is unchanged from a standard SDA of the same bore. Specifications follow the official AirTAC SDAJ datasheet.
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3525 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Force matches a standard SDA of the same bore; the adjuster only sets the stop position, not the area. Actual usable force is lower than theoretical due to friction.
Model Code: Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X60-50S
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 100 | Bore size in mm. |
| ×60 | Maximum stroke length in mm. |
| -50 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Where the Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X60-50S Is Used
Heavy Press Tonnage Setup
Dial in the 10 to 60 mm extend stop during heavy press commissioning to apply precise 3927 N clamping force without swapping mechanical spacers.
Automated Welding Forming
Fine-tune the extend position on the fly for varied metal panel thicknesses, relying on the fixed NBR bumper to absorb the 200.2 kg vertical lift impact.
Large Fixture Positioning
Adjust the stroke endpoint on large assembly fixtures to accommodate part variants, using the magnetic switch for exact extend confirmation.
Is the Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X60-50S the Right Cylinder?
When sizing this 100 mm bore actuator, compare its 3927 N push at 0.5 MPa against the neighbouring SDAJ80, which provides 2513.3 N at the same pressure. Dropping down leaves a 1413.7 N deficit, so if your payload requires the full theoretical 801 kgf at 1.0 MPa, this larger bore is mandatory. The computed safe working load is roughly 2356 N (about 60 percent of the 0.5 MPa figure), allowing a vertical lift of approximately 200.2 kg with a 2:1 safety margin.
Operators needing frequent on-machine stroke tuning for changeovers will benefit from the 50 mm adjustment window. Note that a plain cylinder does not hold its load on air loss or valve centring; the piston drifts and the fixed bumper only decelerates near the end. For secure load holding without live pressure, install an external rod lock or pilot-operated check valve. Confirm your requirements for the 100 mm bore, 60 mm stroke, 50 mm window, PT3/8 port, built-in magnet, and female M18x1.5 rod thread.
Quick checklist
- ✓ Need on-machine stroke fine-tuning?
- ✓ Target position within 10–60 mm
- ✓ Force at your working pressure
- ✓ Access to reach the R adjuster
- ✓ Magnet (S) for sensors?
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Lock the M27×2.0 adjuster after setting the stroke.
- check Avoid side load on the piston rod.
- check Front/rear covers are riveted — do not dismantle.
- check Installation by qualified personnel per AirTAC docs.
Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X60-50S FAQ
At 0.5 MPa it provides 3927 N push and 3524.9 N pull. At 0.7 MPa it provides 5497.8 N push and 4934.8 N pull. The theoretical maximum push is 801 kgf at 1.0 MPa.
The R (M27x2.0) screw mechanically shortens the extend stop from 60 mm down to 10 mm without altering the force. The built-in magnet works with AirTAC reed or electronic switches for position detection.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SDAJ Cylinders
Request a Quote for Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X60-50S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.