The AirTAC Airtac SE ISO 15552 Cylinders SE32X610SG is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 610mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE32X610SG is a double-acting, single-rod ISO 15552 / VDMA 24562 profile cylinder with G1/8 BSPP ports, a built-in sensor magnet and a 610 mm stroke. Its 32 mm bore produces about 402 N push at 0.5 MPa (563 N at 0.7 MPa), running anywhere from 30 to 800 mm/s. The G ports are parallel-threaded, so they seal on a bonded face washer rather than on a taper - a made-to-order thread choice versus the standard PT version, and the right one when your manifold and hose fittings already follow the BSPP standard common on EU and Asian OEM lines. The square extruded aluminum barrel has no external tie rods, so it sits flush against machine plates, resists corrosion and cleans down easily along its three sensor grooves. Both ends carry field-adjustable air cushioning with 27 mm columns: turn the cushion screws to soften hard stops at speed instead of relying on fixed bumpers, and pair the -S magnet with AirTAC CMSE reed or DMSE electronic switches for end-of-stroke feedback over the full 610 mm travel.
| Model | Airtac SE ISO 15552 Cylinders SE32X610SG |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 610 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×610 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
On a case packer discharge, a 610 mm stroke clears finished cartons off a full lane in one push, and 402 N at 0.5 MPa is ample for empty or part-filled boxes - the G1/8 BSPP ports suit the European manifold blocks typically fitted to these machines.
A gap-transfer module raising light totes between two parallel conveyor runs uses the 610 mm travel to cross the full span, while the adjustable cushion at both ends stops each lift smoothly at 30-800 mm/s cycle speeds.
Opening a long sliding guard door on a CNC machining centre needs reach more than muscle: the 610 mm stroke covers the door travel, and the no-tie-rod profile barrel bolts flat to the enclosure frame without protruding hardware.
This is the smallest bore in the SE range, so the only step available is up: if 402 N push at 0.5 MPa is marginal for your load, move to a 40 mm bore, which pushes 628 N at the same pressure on a 16 mm rod. Keep in mind that a plain SE does not hold position when air is exhausted or the valve centres - the piston drifts - so specify the BSE rod-lock variant or a pilot-operated check valve if a 610 mm stroke must stay put under load. For like-for-like ISO 15552 replacement, match the 32 mm bore, 610 mm stroke, G1/8 port style, mounting accessory and rod-end joint, and order the -S magnet only if you need CMSE / DMSE switch sensing. On a 610 mm span with a 12 mm rod, side load and rod-column bending become real: guide the load externally rather than letting the rod bearing take lateral force, and confirm the G (BSPP) thread against your existing fittings and manifold before ordering.
Quick checklist
At 0.5 MPa the 32 mm bore pushes 402 N extending and 345 N retracting (rod area subtracts on the pull side). At 0.7 MPa push rises to 563 N, and at the full 1.0 MPa rating the cylinder reaches a maximum push of 82 kgf. These single-rod figures mean extend force always exceeds retract force on this model.
The trailing G orders G1/8 BSPP ports: a parallel thread that seals on a bonded face washer or O-ring, unlike the tapered PT (Rc) default that seals on the thread itself. Choose G when your existing fittings, hoses or manifold follow the BSPP standard common on EU and Asian-built machines. The cylinder body remains dimensionally interchangeable per ISO 15552, so the G-port version still drops into the same mounting interface as other ISO 15552 cylinders of equal bore and stroke.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.