Airtac TACE Guided Compact Cylinder TACE63X100
The AirTAC Airtac TACE Guided Compact Cylinder TACE63X100 is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø63mm bore and 100mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ63 mm
- Stroke100 mm
- Port size1/8"
- Acting typeDouble acting, non-rotating
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACE Guided Compact Cylinder TACE63X100
The TACE63X100 is a double acting, non-rotating compact cylinder built to ISO 21287: a 63 mm bore and 100 mm stroke on a hard-anodized aluminium body with an S45C hard-chrome plated 16 mm rod. Twin guide rods on a yoke stop the tooling rotating and carry side load, so a gripper or mounting plate stays square without an external guide. At 0.5 MPa it pushes 1558.6 N and pulls 1458.1 N; at 0.7 MPa those figures rise to 2182.1 N push and 2041.3 N pull, with a theoretical peak of 317.9 kgf at 1.0 MPa.
The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight gantries, guards and fixtures where a full-length cylinder will not fit. Plan for about 935 N of real work at 0.5 MPa - roughly 0.6 of the push force - which with a 2:1 margin lifts about 79 kg vertically. A fixed TPU bumper absorbs end-of-stroke energy at both ends, speed spans 30-500 mm/s, and the optional -S magnet enables CMSE / DMSE switches; without it no sensor can be mounted.
Airtac TACE Guided Compact Cylinder TACE63X100 Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE63X100 |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø63 mm |
| Stroke | 100 mm |
| Acting type | Double acting, non-rotating |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø63mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1458 N |
| 0.7 MPa | 2182 N | 2041 N |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE63X100
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 63 | Bore size in mm. |
| ×100 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE63X100 Is Used
Bearing press on an EV module line
The 1558.6 N push at 0.5 MPa presses sealed bearings into aluminium motor housings, and the twin-guide yoke keeps the press plunger square to the bore without a separate guide frame.
Fixture lift in a welding gantry
With about 79 kg of vertical lift at a 2:1 margin, the cylinder raises and lowers steel weld fixtures between stations, and the 100 mm stroke clears the robot envelope.
Heavy-carton pusher on a palletizer
Mounted under the line, it pushes 40 kg cartons sideways into a transfer lane; the compact body fits the 100 mm gap under the conveyor where a profile cylinder would not.
Is the Airtac TACE Guided Compact Cylinder TACE63X100 the Right Cylinder?
Size against neighbours: the 50 mm bore pushes 981.7 N at 0.5 MPa, while stepping up to 80 mm gives 2513.3 N - the 63 mm TACE63X100 sits between them at 1558.6 N push and 1458.1 N pull, a good match for mid-heavy clamping and pressing in a 100 mm stroke. If the load must stay put when air is lost, add a rod lock or pilot check valve, because the piston drifts once pressure drops. Mounting choices are FB flange, CA/CB clevis, CR and FTC; the rod end carries a female M10x1.5 thread and the air port is 1/8" PT. Order the -S code only if you need the magnet for CMSE / DMSE switches.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE63X100 FAQ
At 0.5 MPa it pushes 1558.6 N and pulls 1458.1 N. At 0.7 MPa it pushes 2182.1 N and pulls 2041.3 N. The theoretical maximum is 317.9 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa (22-145 psi) with a proof pressure of 1.5 MPa (215 psi), running on air filtered to 40 um at 30-500 mm/s.
It is an ISO 21287 compact cylinder whose hard-anodized aluminium body saves about 50% of the mounting length of an ISO 15552 profile cylinder, with a fixed TPU bumper at each end to absorb end-of-stroke energy. Mountings are FB flange, CA/CB clevis, CR and FTC, the rod end has a female M10x1.5 thread, and the port is 1/8" PT. The -S magnet is optional: only when it is ordered can CMSE / DMSE switches be mounted; the standard code has no magnet.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE63X100
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.