Airtac TN Double Axis Double Rod Cylinder TN32X100S
The AirTAC Airtac TN Double Axis Double Rod Cylinder TN32X100S is a genuine TN twin-rod (double-rod) double-acting cylinder, 32 mm bore. Two parallel rods on one plate resist bending and twisting and let the load mount without rotating. It delivers about 804.3 N of push at 0.5 MPa. A front bumper cushions the impact and adjusts the stroke over a -5 to 0 mm range.
- TypeTwin-rod, double acting
- Standardenterprise standard
- Bore32 mm
- Push thrust @0.5 MPa804.3 N
- Operating pressure0.15 - 1.0 MPa (22 - 145 psi)
- Port size1/8"
- CushionAdjustable bumper (-5 to 0 mm)
- MagnetStandard (sensor-ready)
- ThreadPT
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TN Double Axis Double Rod Cylinder TN32X100S
A twin-rod, double-acting cylinder uses two parallel rods on one shared plate, so the mounted load cannot rotate and the plate resists bending and twisting forces. With a 32 mm bore and 100 mm stroke, the push side delivers about 804 N of theoretical thrust at 0.5 MPa, suiting it to pushing, clamping and lift jobs where a single-rod cylinder would need external anti-rotation guidance. The external bumper on the front cover cushions impact and adjusts the effective stroke over -5 to 0 mm.
This is a genuine AirTAC part from the TN series, built to the Enterprise standard, with the magnet fitted as standard and magnetic-switch slots around the body. It runs on 40 um filtered air at 0.15-1.0 MPa (22-145 psi), -20 to 70 C, at 30-500 mm/s. We confirm exact dimensions, weights and side-load curves from the datasheet on request.
Airtac TN Double Axis Double Rod Cylinder TN32X100S Technical Specifications
| Model | Airtac TN Double Axis Double Rod Cylinder TN32X100S |
|---|---|
| Type | Twin-rod cylinder, double acting |
| Series / standard | TN (enterprise standard) |
| Bore | 32 mm |
| Push thrust @0.5 MPa | 804.3 N |
| Port size | 1/8" (PT thread) |
| Fluid | Air, filtered to 40 um |
|---|---|
| Operating pressure | 0.15 - 1.0 MPa (22 - 145 psi) |
| Proof pressure | 1.5 MPa (215 psi) |
| Temperature | -20 to 70 C |
| Speed range | 30 - 500 mm/s |
| Cushion | Bumper, stroke adjustable -5 to 0 mm |
| Magnet | Standard (magnetic-switch slots around the body) |
Specifications follow the official AirTAC TN/TR twin-rod data. Operating pressure is set by bore (0.2 MPa minimum on the 6 and 10 mm bores). The front cover and piston are short, so avoid an over-long stroke. Overall dimensions vary per stroke and allowable side-load is published as curves — ask us and we confirm from the datasheet.
How to choose
Choose bore 32 when you need roughly 804 N of push at 0.5 MPa (push exceeds pull); for lighter loads, smaller TN/TR bores are available in the same twin-rod layout. This TN model is the Enterprise-standard series and carries PT ports only - the JIS-standard TR series adds G and NPT options plus a precise lengthening sliding-support guide and two groups of ports, one each side, if your application needs tighter guide accuracy. The 100 mm stroke is within this bore's table, but keep to table lengths: over-long twin-rod strokes increase rod-end deflection, and side-load limits are published as curves we confirm from the datasheet.
Applications
Packaging line pusher
The wide non-rotating plate pushes product cartons squarely into an end-of-line case packer over the 100 mm stroke, with the bumper softening each advance.
Transfer shuttle slide
Mounted under a shuttle table, the twin rods move parts between two machining stations without the plate twisting, keeping parts aligned at both stops.
Clamp-and-hold station
The plate closes on a workpiece in a welding fixture and holds it square while it is tacked; magnetic switches on the body signal clamp-complete.
FAQ
How do I choose between TN and TR twin-rod cylinders?
TN is the Enterprise-standard series with PT thread only. TR is the JIS-standard series, adding G and NPT thread choices, two groups of ports on both sides, higher non-rotating precision and a lengthening sliding-support guide that needs no added lubricant. Pick TR when guide precision or thread type demands it.
Can the plate take side loads directly?
The twin rods give the plate good resistance to bending and twisting, so loads mount without rotating, but allowable side load and rod-end deflection are published only as curves. Send us your side-load and stroke details and we confirm the limits from the datasheet.