AirTAC 3V100M-13 3V-F Base (3V100M13F)
The AirTAC AirTAC 3V100M-13 3V-F Base (3V100M13F) is a genuine 3V-F manifold base manifold base for 13 stations on one shared air supply. A base is a machined block: it carries no coil and no solenoid, so the valves that sit on it are ordered separately.
- Valve type3/2-way (3-port, 2-position)
- Stations13
- Series3V-F manifold base
About the AirTAC 3V100M-13 3V-F Base (3V100M13F)
3V100M13F is AirTAC's thirteen-station manifold base for 3/2 valves. Instead of bolting thirteen separate valves to thirteen individual supplies, the block hands every station the same air from one inlet, which keeps large single-acting circuits tidy and traceable.
This listing is the base alone - a genuine AirTAC component with no coil, no state and no electrical data of its own. The valves, in NC or NO, five coil voltages and either electrical entry, are ordered separately; bases in this family run from 1F to 20F stations. We will confirm datasheet details for base and valves on request.
AirTAC 3V100M-13 3V-F Base (3V100M13F) Technical Specifications
| Model | AirTAC 3V100M-13 3V-F Base (3V100M13F) |
|---|---|
| Series | 3V-F manifold base |
| Item form | Manifold base (no coil, no solenoid, no initial state) |
| Stations | 13 |
| Port size | Confirm from the datasheet — ask us |
| Thread | PT |
| Operating pressure | Confirm from the datasheet — ask us |
|---|---|
| Flow coefficient | Confirm from the datasheet — ask us |
| Temperature | Confirm from the datasheet — ask us |
| Protection | Confirm from the datasheet — ask us |
Model Code: AirTAC 3V100M-13 3V-F Base (3V100M13F)
| 3V-F manifold base | Body. |
|---|---|
| 13F | 13 stations in one assembly. |
| PT | Port thread. PT ships from stock; G and NPT are available to order. |
What a 3/2 Valve Does
A 3/2 valve has three ports — supply, outlet and exhaust — and two states. It either feeds the outlet or vents it to exhaust, and that is the whole job.
That makes it the right valve for a single-acting (spring-return) cylinder, on/off air blow, a clamp, switching a vacuum generator or suction cup, and piloting a larger valve.
It cannot run a double-acting cylinder. A double-acting cylinder needs air alternately on two sides, which takes a 5-port valve — the AirTAC 4V series.
Where the AirTAC 3V100M-13 3V-F Base (3V100M13F) Is Used
Test rig sequencing
A leakage or function test rig with more than a dozen spring-return actuators can assign one station per actuator on the 13-way block.
Central air take-off
Mounting the base near the filter-regulator gives every downstream single-acting device a short, common feed path.
Laboratory automation
Sample handling rigs that lift or clamp with spring-return cylinders can drive each function from its own valve on the shared base.
Is the AirTAC 3V100M-13 3V-F Base (3V100M13F) the Right Part?
A thirteen-station base fits circuits that have outgrown smaller blocks: test rigs, multi-station fixtures, dense distribution panels. Plan it in two passes - first fix the air side (one supply, one filter, one isolator for the whole group), then order the valves station by station, choosing NC or NO for the fail-safe behaviour you want at each actuator, the coil voltage that matches your panel, and DIN plug or flying lead to suit the wiring. Two routing notes before you buy: we hold no published flow figures for this family, so ask us to verify sizing against your actuators via RFQ, and if documented flow and coil-power data is a hard requirement today, the 3V2 and 3V3 bodies are the AirTAC valves that publish it. For double-acting cylinders, move to the 5-port AirTAC 4V series.
Confirm before you order
- ✓ Port size and thread (PT from stock; G / NPT to order)
- ✓ Initial state — NC or NO, ordered up front
- ✓ Coil voltage matches your controller output
- ✓ Electrical entry — DIN plug or flying lead
- ✓ Single valve, bare base, or complete assembly
- ✓ Single-acting duty, not double-acting
Installation & Wiring Notes
- check Use clean air filtered to 40µm or finer.
- check Use the manual override to test before powering up.
- check Leave the exhaust port clear, or fit a silencer.
- check Blank any unused station on the base before pressurising.
- check Wiring by qualified personnel, per AirTAC documentation.
AirTAC 3V100M-13 3V-F Base (3V100M13F) FAQ
It is a machined manifold block, so it has no coil, no state and no electrical figures of its own. We will confirm its datasheet details on request and do the same for any valves you mount on it; the 3V2 and 3V3 series are the AirTAC bodies with published flow and coil-power figures if you need them immediately.
Yes - each valve is ordered separately, so stations can mix NC and NO, different coil voltages and either electrical entry as your circuit demands. One limit to respect: a 3/2 valve feeds or vents a single outlet and cannot drive a double-acting cylinder, which is a job for the 5-port AirTAC 4V series.
Authorized Export Seller
Genuine AirTAC parts produced by the AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC 3V Valves
Request a Quote for AirTAC 3V100M-13 3V-F Base (3V100M13F)
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.