Airtac 3V-F Base 3V200M2F
The AirTAC Airtac 3V-F Base 3V200M2F is a genuine 3V-F manifold base manifold base for 2 stations on one shared air supply. A base is a machined block: it carries no coil and no solenoid, so the valves that sit on it are ordered separately.
- Valve type3/2-way (3-port, 2-position)
- Stations2
- Series3V-F manifold base
About the Airtac 3V-F Base 3V200M2F
The 3V200M2F is a compact two-station base from AirTAC's 3V2 family: a machined manifold block that carries two separately ordered 3/2 solenoid valves on one shared air supply. Each valve keeps its own supply, outlet and exhaust ports and its own coil, so the pair can do two unrelated jobs - one clamping while the other blows off.
This is a genuine AirTAC part. The valves are ordered separately, so choose a normally closed or normally open version for each station, match each coil to the panel voltage across five options, and pick DIN plug or flying lead per valve. Shorter and longer bases exist across the family too. Ask us before ordering and we will confirm the datasheet figures for the exact valves you select.
Airtac 3V-F Base 3V200M2F Technical Specifications
| Model | Airtac 3V-F Base 3V200M2F |
|---|---|
| Series | 3V-F manifold base |
| Item form | Manifold base (no coil, no solenoid, no initial state) |
| Stations | 2 |
| Port size | Confirm from the datasheet — ask us |
| Thread | PT |
| Operating pressure | Confirm from the datasheet — ask us |
|---|---|
| Flow coefficient | Confirm from the datasheet — ask us |
| Temperature | Confirm from the datasheet — ask us |
| Protection | Confirm from the datasheet — ask us |
Model Code: Airtac 3V-F Base 3V200M2F
| 3V-F manifold base | Body. |
|---|---|
| 2F | 2 stations in one assembly. |
| PT | Port thread. PT ships from stock; G and NPT are available to order. |
What a 3/2 Valve Does
A 3/2 valve has three ports — supply, outlet and exhaust — and two states. It either feeds the outlet or vents it to exhaust, and that is the whole job.
That makes it the right valve for a single-acting (spring-return) cylinder, on/off air blow, a clamp, switching a vacuum generator or suction cup, and piloting a larger valve.
It cannot run a double-acting cylinder. A double-acting cylinder needs air alternately on two sides, which takes a 5-port valve — the AirTAC 4V series.
Where the Airtac 3V-F Base 3V200M2F Is Used
Small workholding fixture pair
Clamp and unclamp two toggle stations on a small drilling fixture, both fed from one air drop and venting independently.
Chip clearing on a manual lathe
One station blows chips clear of the cutting zone on demand while the other holds the pneumatic stop for the bar feed.
Wire and cable machine hold-downs
Switch the two hold-down cylinders on a wire processing machine, each timed and exhausted by its own valve.
Is the Airtac 3V-F Base 3V200M2F the Right Part?
Two stations suit a small machine that needs two independent 3/2 functions - say a clamp and a cleaning jet - without two separate supply runs. Specify each valve on its own merits: NC if the load must vent on power loss, NO if it must stay fed, and a coil voltage that matches the panel because coils are not rewirable. Send us the two duties and we will confirm sizing against your actuators from the datasheet before you order; where you want flow and coil power published up front, the documented 3V2 (1/8 in and 1/4 in) and 3V3 (1/4 in) bodies are the alternative, and a double-acting cylinder calls for the AirTAC 4V series.
Confirm before you order
- ✓ Port size and thread (PT from stock; G / NPT to order)
- ✓ Initial state — NC or NO, ordered up front
- ✓ Coil voltage matches your controller output
- ✓ Electrical entry — DIN plug or flying lead
- ✓ Single valve, bare base, or complete assembly
- ✓ Single-acting duty, not double-acting
Installation & Wiring Notes
- check Use clean air filtered to 40µm or finer.
- check Use the manual override to test before powering up.
- check Leave the exhaust port clear, or fit a silencer.
- check Blank any unused station on the base before pressurising.
- check Wiring by qualified personnel, per AirTAC documentation.
Airtac 3V-F Base 3V200M2F FAQ
Those figures are not published on this page; list your two duties in an RFQ and we will confirm the datasheet numbers for the valves we propose. Where published flow and coil-power figures are needed immediately, the 3V2 and 3V3 series carry them.
Two valves, one per station, each specified separately for state (NC or NO), port size, coil voltage and electrical entry, plus your filtration and fittings. The base has no coil or wiring of its own; and if any load is a double-acting cylinder, that job belongs to a 5-port AirTAC 4V valve, not a 3/2.
Authorized Export Seller
Genuine AirTAC parts produced by the AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC 3V Valves
Request a Quote for Airtac 3V-F Base 3V200M2F
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.