Airtac 3V2M Solenoid Valve 3V2MNOEI-9F
The AirTAC Airtac 3V2M Solenoid Valve 3V2MNOEI-9F is a genuine 3-port 2-position (3/2) solenoid valve with 1/8 in ports. It either feeds its outlet or vents it to exhaust, which is what makes it the valve for single-acting cylinders, on/off air blow, clamping, vacuum switching and pilot duty.
- Valve type3/2-way (3-port, 2-position)
- Initial stateNormally open
- Port size1/8 in
- Coil voltageAC24V
- Electrical entryFlying lead (lead-out wire type)
- Stations9
- Flow (Cv)0.1
- Series3V2M
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac 3V2M Solenoid Valve 3V2MNOEI-9F
Nine valves sharing one supply gallery and one wiring bus is what makes this 9F assembly quick to troubleshoot: a station that misbehaves stands out against neighbours fed under identical conditions. Each valve is a 3/2 normally open, direct-acting, spring-return unit with coaxial poppet sealing, Cv 0.1 and PT1/8 ports.
Total coil load at AC24V is 7 VA per station, so a fully energised bank draws about 63 VA - size your transformer for that ceiling. Exhaust is centralised through the base, keeping the outside of the machine clean. IP65 coil protection (DIN 40050) suits dusty plant environments, and a manual override on every body speeds up set-up and fault tracing.
Airtac 3V2M Solenoid Valve 3V2MNOEI-9F Technical Specifications
| Model | Airtac 3V2M Solenoid Valve 3V2MNOEI-9F |
|---|---|
| Series | 3V2M |
| Valve type | 3/2-way (3-port, 2-position) |
| Function | Direct-acting, single solenoid, spring return |
| Initial state | Normally open |
| Item form | Complete assembly — 9 valves on a shared base |
| Exhaust | Centralised exhaust |
| Port size | 1/8 in |
| Thread | PT |
| Coil voltage | AC24V |
|---|---|
| Electrical entry | Flying lead (lead-out wire type) |
| Coil power | 7 VA |
| Operating pressure | 0-0.8 MPa (0-114 psi) |
| Vacuum service | Not rated for vacuum |
| Flow coefficient | Cv 0.1 |
| Temperature | -20 to 70 C |
| Construction | Coaxial shut-off (poppet), base-mounted, spring return |
| Protection | IP65 (DIN 40050) |
| Medium | Air, filtered by a 40 µm or finer element. Lubrication not required. |
Figures follow the official AirTAC 3V2M catalogue. Confirm coil voltage and thread (PT / NPT / G) against the product label before wiring.
Model Code: Airtac 3V2M Solenoid Valve 3V2MNOEI-9F
| 3V2M | Body — sets the flow, the coil power and whether vacuum is rated. |
|---|---|
| 1/8 in | Port size. M5, 06 = 1/8 in, 08 = 1/4 in, 10 = 3/8 in. |
| NO | Normally open: air passes until the coil is energised. |
| AC24V | Coil voltage. A = AC220V, B = DC24V, C = AC110V, E = AC24V, F = DC12V. |
| I | Electrical entry: I = flying lead, otherwise a DIN plug. |
| 9F | 9 stations in one assembly, centralised exhaust. |
| PT | Port thread. PT ships from stock; G and NPT are available to order. |
What a 3/2 Valve Does
A 3/2 valve has three ports — supply, outlet and exhaust — and two states. It either feeds the outlet or vents it to exhaust, and that is the whole job.
That makes it the right valve for a single-acting (spring-return) cylinder, on/off air blow, a clamp, switching a vacuum generator or suction cup, and piloting a larger valve.
It cannot run a double-acting cylinder. A double-acting cylinder needs air alternately on two sides, which takes a 5-port valve — the AirTAC 4V series.
Where the Airtac 3V2M Solenoid Valve 3V2MNOEI-9F Is Used
Test-rig pin sequencing
A materials test rig cycles nine single-acting loading pins in sequence; identical supply and wiring conditions make an off-spec station obvious at a glance.
Web-tension idler arms
Nine idler rollers on a paper converting line each carry a set pneumatic load; the NO valve vents a station only when the controller calls for release.
Tile press ejectors
Ejector pins across a ceramic tile mould drop finished parts station by station, all fed from one PT1/8 supply gallery and vented through one port.
Is the Airtac 3V2M Solenoid Valve 3V2MNOEI-9F the Right Part?
Treat Cv 0.1 as the price of manifold density: the flow path runs through the 9F base, so per-station flow is lower than the stand-alone 3V2 (Cv 0.18 at 1/8, Cv 0.19 at 1/4, vacuum-rated) and much lower than 3V3 (Cv 0.62, 1/4, vacuum-rated). For modest duties where power matters more than flow, 3V1 at 3.0 W DC is the leaner pick. If the actuator is double-acting, the 3/2 format cannot serve it - move to the AirTAC 4V series.
Nothing on 3V2M converts NO to NC after purchase; the initial state is sealed in at the factory. So before you RFQ, confirm: normally open state, AC24V coil, flying-lead entry, nine stations, centralised exhaust, and thread - PT1/8 is standard, while G and NPT are options you specify at order time.
Confirm before you order
- ✓ Port size and thread (PT from stock; G / NPT to order)
- ✓ Initial state — NC or NO, ordered up front
- ✓ Coil voltage matches your controller output
- ✓ Electrical entry — DIN plug or flying lead
- ✓ Single valve, bare base, or complete assembly
- ✓ Single-acting duty, not double-acting
Installation & Wiring Notes
- check Use clean air filtered to 40µm or finer.
- check Stay within 0-0.8 MPa (0-114 psi) operating pressure.
- check Match the coil voltage to your controller output.
- check Use the manual override to test before powering up.
- check Leave the exhaust port clear, or fit a silencer.
- check Blank any unused station on the base before pressurising.
- check Wiring by qualified personnel, per AirTAC documentation.
Airtac 3V2M Solenoid Valve 3V2MNOEI-9F FAQ
Nine 3/2 direct-acting, spring-return stations, normally open, Cv 0.1 each, 0-0.8 MPa operating pressure, -20 to 70 C, AC24V coils at 7 VA each (DC types 7.0 W), IP65 to DIN 40050, PT1/8 ports with G and NPT as order options, centralised exhaust and flying-lead wiring.
NO logic suits circuits where the outlet must pass air as soon as supply is present and vent only on command - common with clamps that must stay engaged through a power cut. The state cannot be converted afterwards: the dedicated base gasket does not reverse NC to NO, so the correct state must be ordered up front.
Authorized Export Seller
Genuine AirTAC parts produced by the AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC 3V Valves
Request a Quote for Airtac 3V2M Solenoid Valve 3V2MNOEI-9F
Send us the quantity, coil voltage and destination. We confirm price, stock and lead time — usually within 7-8 hours.