Airtac JSI Series Standard Cylinder JSI100X200S
The AirTAC Airtac JSI Series Standard Cylinder JSI100X200S is a genuine double acting JIS-standard air cylinder with a Ø100mm bore and 200mm stroke, G1/2 air ports and adjustable end cushioning. Its no-tie-rod, hard-anodized profile barrel is more compact than an ISO 15552 cylinder of the same bore — a space-saver on tight machines.
- BoreØ100 mm
- Stroke200 mm
- Port sizeG1/2
- Acting typeDouble acting
- Rod threadM26×1.5
- CushionAdjustable, 33 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac JSI Series Standard Cylinder JSI100X200S
Delivering 3927 N of push force at 0.5 MPa, this double-acting 100 mm bore JIS-standard profile cylinder saves valuable machine space by being noticeably shorter than an equivalent ISO 15552 unit of the same bore. The extruded hard-anodized aluminum barrel omits external rods to resist wear, while a two-way piston seal retains grease for a long, low-friction service life. Equipped with a G1/2 port and an M26x1.5 rod thread, it is built for heavy-duty cycling.
Because the -S suffix denotes a built-in piston magnet, this model is ready for CMSE or DMSE electronic switches that drop directly into the side sensor grooves for precise positioning. For real-world sizing, plan for about 2356 N of actual work at 0.5 MPa, which translates to lifting roughly 200 kg vertically with a sensible 2:1 safety margin.
Airtac JSI Series Standard Cylinder JSI100X200S Technical Specifications
| Model | Airtac JSI Series Standard Cylinder JSI100X200S |
|---|---|
| Series | JSI JIS-standard profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 200 mm |
| Acting type | Double acting |
| Port size | G1/2 |
| Rod thread | M26×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 33 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC JSI (JIS standard) datasheet. Confirm against the product label before installation. Thread options: PT (blank) / G. Barrel: hard-anodized aluminum profile (no tie rods).
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3525 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac JSI Series Standard Cylinder JSI100X200S
| JSI | JIS-standard profile cylinder (double-acting type). |
|---|---|
| 100 | Bore size in mm (32 / 40 / 50 / 63 / 80 / 100 / 125). |
| ×200 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensors. |
JSI-family variants: JSI (double acting), JSID (double rod), JSIJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / TCM1 / TCM2. Thread PT (blank) / G.
Where the Airtac JSI Series Standard Cylinder JSI100X200S Is Used
Injection Mold Clamping
Provides the high 3927 N push force needed to secure heavy injection mold halves or hold large industrial dies in place during machining operations.
Pallet Dispenser Pusher
Exerts robust thrust to separate and feed empty pallets from a magazine stack, utilizing the 200 mm stroke to index heavy loads smoothly.
Heavy Package Diverter
Actuates a heavy-duty routing gate on a high-speed logistics conveyor, using the built-in magnet to confirm full extension via DMSE sensors.
Is the Airtac JSI Series Standard Cylinder JSI100X200S the Right Cylinder?
When sizing this 100 mm bore actuator, stepping down to a JSI63 provides 1559 N of push force at 0.5 MPa, while stepping up to the massive JSI125 yields 6136 N. This JSI100X200S hits a strong middle ground for 3927 N loads. The included -S magnet pairs perfectly with CMSE or DMSE sensors for end-of-stroke detection. Remember that a standard cylinder will drift and cannot hold a load if air pressure is lost or the valve is centered; the adjustable 33 mm air cushions only decelerate the piston near the end of stroke rather than locking it. To suspend a load safely, install an external rod lock or a pilot-operated check valve.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac JSI Series Standard Cylinder JSI100X200S FAQ
This 100 mm bore cylinder features a G1/2 air port, an M26x1.5 rod thread, and a 32 mm piston rod. It delivers 3927 N push and 3574 N pull at 0.5 MPa, 5497 N push and 5003 N pull at 0.7 MPa, with a theoretical maximum force of 801 kgf at 1.0 MPa.
The JIS-standard profile body is noticeably shorter and more compact than an ISO 15552 cylinder of the same 100 mm bore, saving machine space without sacrificing power. It uses a hard-anodized extruded aluminum barrel with no external rods, and the -S magnet version allows CMSE or DMSE sensors to slot directly into the side grooves.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC JSI Cylinders
Request a Quote for Airtac JSI Series Standard Cylinder JSI100X200S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.