Airtac JSI Series Standard Cylinder JSI100X35
The AirTAC Airtac JSI Series Standard Cylinder JSI100X35 is a genuine double acting JIS-standard air cylinder with a Ø100mm bore and 35mm stroke, G1/2 air ports and adjustable end cushioning. Its no-tie-rod, hard-anodized profile barrel is more compact than an ISO 15552 cylinder of the same bore — a space-saver on tight machines.
- BoreØ100 mm
- Stroke35 mm
- Port sizeG1/2
- Acting typeDouble acting
- Rod threadM26×1.5
- CushionAdjustable, 33 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac JSI Series Standard Cylinder JSI100X35
Delivering 3927 N of push force at 0.5 MPa, this double-acting JIS-standard profile cylinder is built for heavy-duty compact machinery. Its extruded hard-anodized aluminum barrel sheds external rods to save space, measuring shorter than an ISO 15552 cylinder of the same 100 mm bore. The internal two-way piston seal retains grease for a long, low-friction service life.
Plan for about 2356 N of real work at 0.5 MPa, which safely lifts a 200 kg vertical load with a 2:1 margin. Air enters via a G1/2 port, and adjustable 33 mm cushions decelerate the 32 mm rod at both stroke ends. Because this specific SKU lacks the -S magnet, it cannot host CMSE or DMSE position switches.
Airtac JSI Series Standard Cylinder JSI100X35 Technical Specifications
| Model | Airtac JSI Series Standard Cylinder JSI100X35 |
|---|---|
| Series | JSI JIS-standard profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 35 mm |
| Acting type | Double acting |
| Port size | G1/2 |
| Rod thread | M26×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 33 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC JSI (JIS standard) datasheet. Confirm against the product label before installation. Thread options: PT (blank) / G. Barrel: hard-anodized aluminum profile (no tie rods).
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3525 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac JSI Series Standard Cylinder JSI100X35
| JSI | JIS-standard profile cylinder (double-acting type). |
|---|---|
| 100 | Bore size in mm (32 / 40 / 50 / 63 / 80 / 100 / 125). |
| ×35 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensors. |
JSI-family variants: JSI (double acting), JSID (double rod), JSIJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / TCM1 / TCM2. Thread PT (blank) / G.
Where the Airtac JSI Series Standard Cylinder JSI100X35 Is Used
Press Fit Assembly
Drives heavy bearings into automotive transmission housings using its 3927 N push force at 0.5 MPa.
Pallet Stopper Gate
Acts as a robust 100 mm bore stopper block on high-mass conveyor lines, handling impacts without tie rods.
Heavy Carton Flap Folder
Folds thick corrugated flaps on large appliance cartons, relying on the 35 mm short stroke for rapid cycling.
Is the Airtac JSI Series Standard Cylinder JSI100X35 the Right Cylinder?
If 3927 N at 0.5 MPa is too much force, the neighboring 80 mm bore provides 2513 N; stepping up to the 125 mm bore yields 6136 N. This 35 mm stroke moves quickly within the 30-800 mm/s speed range. For mounting flexibility, choose LB foot, FA/FB flange, CA/CB/CR clevis, TC/TCM1/TCM2 trunnion, or an I/Y/F/U rod knuckle.
Remember that standard air cushions only decelerate the piston near the end of travel and do not function as a brake. If your application must hold a load vertically during air loss or valve centering, add an external rod lock or a pilot-operated check valve to prevent drift.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac JSI Series Standard Cylinder JSI100X35 FAQ
The 100 mm bore uses a G1/2 port. At 0.5 MPa it pushes 3927 N and pulls 3574 N. At 0.7 MPa it pushes 5497 N and pulls 5003 N. The theoretical maximum force is 801 kgf at 1.0 MPa.
It is a JIS-standard profile cylinder that is shorter and more compact than an ISO 15552 cylinder of the same bore. Note that this specific SKU has no -S magnet, so it cannot accept CMSE or DMSE sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC JSI Cylinders
Request a Quote for Airtac JSI Series Standard Cylinder JSI100X35
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.