Airtac JSI Series Standard Cylinder JSI32X350
The AirTAC Airtac JSI Series Standard Cylinder JSI32X350 is a genuine double acting JIS-standard air cylinder with a Ø32mm bore and 350mm stroke, G1/8 air ports and adjustable end cushioning. Its no-tie-rod, hard-anodized profile barrel is more compact than an ISO 15552 cylinder of the same bore — a space-saver on tight machines.
- BoreØ32 mm
- Stroke350 mm
- Port sizeG1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 20 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac JSI Series Standard Cylinder JSI32X350
Generating 402 N of push force at 0.5 MPa, this double-acting JIS-standard profile cylinder saves valuable machine space by being noticeably shorter than an ISO 15552 cylinder of the same 32 mm bore. The extruded hard-anodized aluminum barrel omits external rods to resist wear, while a two-way piston seal retains grease for long, low-friction life. Plan for roughly 241 N of real work at 0.5 MPa, which translates to lifting about 20 kg vertically with a 2:1 safety margin.
Because this specific SKU lacks the -S magnet, it cannot accept CMSE or DMSE position switches. Air connections use a G1/8 port, and the 12 mm carbon steel rod features an M10x1.25 thread. The adjustable air cushion at both ends decelerates the piston over 20 mm near stroke end.
Airtac JSI Series Standard Cylinder JSI32X350 Technical Specifications
| Model | Airtac JSI Series Standard Cylinder JSI32X350 |
|---|---|
| Series | JSI JIS-standard profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 350 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 20 mm |
| Max standard stroke | Up to 1000 mm |
Specifications follow the official AirTAC JSI (JIS standard) datasheet. Confirm against the product label before installation. Thread options: PT (blank) / G. Barrel: hard-anodized aluminum profile (no tie rods).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac JSI Series Standard Cylinder JSI32X350
| JSI | JIS-standard profile cylinder (double-acting type). |
|---|---|
| 32 | Bore size in mm (32 / 40 / 50 / 63 / 80 / 100 / 125). |
| ×350 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensors. |
JSI-family variants: JSI (double acting), JSID (double rod), JSIJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / TCM1 / TCM2. Thread PT (blank) / G.
Where the Airtac JSI Series Standard Cylinder JSI32X350 Is Used
Small Part Ejection
Pushes lightweight plastic mouldings out of an injection press using 402 N of push force at 0.5 MPa over a 350 mm reach.
Packaging Diverter
Actuates a routing flap on a compact packaging line where the shorter JIS profile saves critical clearance.
Test Fixture Actuation
Moves a 15 kg test probe array vertically into position, well within the 20 kg safe vertical lift capacity.
Is the Airtac JSI Series Standard Cylinder JSI32X350 the Right Cylinder?
When sizing this 32 mm bore, stepping up to the JSI40X350 yields 628 N of push at 0.5 MPa, while there is no smaller JSI option available if you need less force. Since this is a plain cylinder without a magnet, you cannot mount reed or solid-state sensors directly; choose an -S variant if you need CMSE or DMSE detection. If your process must maintain a vertical position during air loss or valve centering, note that the piston will drift, so an external rod lock or pilot-operated check valve is required.
At a 350 mm stroke, the 12 mm rod is susceptible to bending under lateral stress. Always guide the load externally to prevent side-loading and ensure the force remains strictly axial.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac JSI Series Standard Cylinder JSI32X350 FAQ
This 32 mm bore cylinder features a G1/8 port and delivers a push of 402 N and pull of 345 N at 0.5 MPa. At 0.7 MPa, push is 563 N and pull is 483 N. The theoretical maximum force is 82 kgf at 1.0 MPa.
The JSI series follows JIS standards and uses an extruded aluminum barrel without external rods, making it shorter and more compact than an ISO 15552 cylinder of the same bore. This design is ideal for tight machine layouts.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC JSI Cylinders
Request a Quote for Airtac JSI Series Standard Cylinder JSI32X350
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.