Airtac JSI Series Standard Cylinder JSI32X40
The AirTAC Airtac JSI Series Standard Cylinder JSI32X40 is a genuine double acting JIS-standard air cylinder with a Ø32mm bore and 40mm stroke, G1/8 air ports and adjustable end cushioning. Its no-tie-rod, hard-anodized profile barrel is more compact than an ISO 15552 cylinder of the same bore — a space-saver on tight machines.
- BoreØ32 mm
- Stroke40 mm
- Port sizeG1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 20 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac JSI Series Standard Cylinder JSI32X40
Generating 402 N of push force at 0.5 MPa, this double-acting 32 mm bore cylinder fits tight machine layouts. Its JIS-standard extruded aluminium profile is noticeably shorter than an ISO 15552 unit of the same bore. The hard-anodized barrel omits external rods to resist wear, while the two-way piston seal retains grease for a long, low-friction service life.
Because this SKU lacks the -S magnet, it cannot accept CMSE or DMSE position switches. For sizing real work, plan for roughly 241 N of usable load at 0.5 MPa, which equates to lifting about 20 kg vertically with a 2:1 safety margin. Air connects via a G1/8 port, and adjustable cushions decelerate the 12 mm rod at both stroke ends.
Airtac JSI Series Standard Cylinder JSI32X40 Technical Specifications
| Model | Airtac JSI Series Standard Cylinder JSI32X40 |
|---|---|
| Series | JSI JIS-standard profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 40 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 20 mm |
| Max standard stroke | Up to 1000 mm |
Specifications follow the official AirTAC JSI (JIS standard) datasheet. Confirm against the product label before installation. Thread options: PT (blank) / G. Barrel: hard-anodized aluminum profile (no tie rods).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac JSI Series Standard Cylinder JSI32X40
| JSI | JIS-standard profile cylinder (double-acting type). |
|---|---|
| 32 | Bore size in mm (32 / 40 / 50 / 63 / 80 / 100 / 125). |
| ×40 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensors. |
JSI-family variants: JSI (double acting), JSID (double rod), JSIJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / TCM1 / TCM2. Thread PT (blank) / G.
Where the Airtac JSI Series Standard Cylinder JSI32X40 Is Used
Small Part Ejection
Pushes lightweight plastic mouldings out of an injection press with 402 N, safely handling parts under the 20 kg vertical lift threshold.
PCB Clamp Actuation
Cycles a 40 mm stroke to secure delicate circuit boards during routing, using the compact JIS profile to save valuable floor space.
Divert Gate Trigger
Moves a lightweight sorting flap on a packaging line, where the hard-anodized barrel withstands repetitive daily cycling.
Is the Airtac JSI Series Standard Cylinder JSI32X40 the Right Cylinder?
If 402 N of push is too much for delicate parts, AirTAC does not offer a smaller JSI bore, so you must add external flow controls or regulator pressure. Stepping up to the JSI40X40 yields 628 N at 0.5 MPa. Keep in mind this plain cylinder drifts if air pressure drops or the valve centers; the cushions only slow the piston near stroke ends, so fit an external rod lock or pilot-operated check valve if you need to hold a load. Without the -S magnet option, this specific model cannot host magnetic sensors.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac JSI Series Standard Cylinder JSI32X40 FAQ
This 32 mm bore model uses a G1/8 port. It delivers 402 N push and 345 N pull at 0.5 MPa, 563 N push and 483 N pull at 0.7 MPa, with a theoretical maximum of 82 kgf at 1.0 MPa.
The JSI is a JIS-standard profile cylinder that is shorter and more compact than an ISO 15552 cylinder of the same 32 mm bore. It uses an extruded aluminum barrel without external rods to achieve this space saving.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC JSI Cylinders
Request a Quote for Airtac JSI Series Standard Cylinder JSI32X40
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.