Airtac JSI Series Standard Cylinder JSI32X500
The AirTAC Airtac JSI Series Standard Cylinder JSI32X500 is a genuine double acting JIS-standard air cylinder with a Ø32mm bore and 500mm stroke, G1/8 air ports and adjustable end cushioning. Its no-tie-rod, hard-anodized profile barrel is more compact than an ISO 15552 cylinder of the same bore — a space-saver on tight machines.
- BoreØ32 mm
- Stroke500 mm
- Port sizeG1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 20 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac JSI Series Standard Cylinder JSI32X500
Delivering 402 N of push force at 0.5 MPa, this double-acting JIS-standard profile cylinder saves valuable machine space by being noticeably shorter than an ISO 15552 cylinder of the same 32 mm bore. The extruded hard-anodized aluminum barrel omits external rods to resist wear, while a two-way piston seal retains grease for long, low-friction life. Air connects via a G1/8 port.
Because this SKU lacks the -S magnet, it cannot accept CMSE or DMSE position switches. For real-world sizing, plan for about 241 N of actual work at 0.5 MPa, which translates to lifting roughly 20 kg vertically with a 2:1 safety margin.
Airtac JSI Series Standard Cylinder JSI32X500 Technical Specifications
| Model | Airtac JSI Series Standard Cylinder JSI32X500 |
|---|---|
| Series | JSI JIS-standard profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 500 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 20 mm |
| Max standard stroke | Up to 1000 mm |
Specifications follow the official AirTAC JSI (JIS standard) datasheet. Confirm against the product label before installation. Thread options: PT (blank) / G. Barrel: hard-anodized aluminum profile (no tie rods).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac JSI Series Standard Cylinder JSI32X500
| JSI | JIS-standard profile cylinder (double-acting type). |
|---|---|
| 32 | Bore size in mm (32 / 40 / 50 / 63 / 80 / 100 / 125). |
| ×500 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensors. |
JSI-family variants: JSI (double acting), JSID (double rod), JSIJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / TCM1 / TCM2. Thread PT (blank) / G.
Where the Airtac JSI Series Standard Cylinder JSI32X500 Is Used
Lightweight Drawer Pusher
Uses the full 500 mm travel to index small material trays in an electronics assembly line, safely moving parts weighing under 20 kg.
Packaging Diverter
Pushes lightweight cardboard cartons at 30-800 mm/s onto a secondary conveyor belt during automated packing runs.
Lab Sample Handler
Extends to transfer small specimen racks between testing stations where a compact 32 mm bore footprint is required.
Is the Airtac JSI Series Standard Cylinder JSI32X500 the Right Cylinder?
If 402 N at 0.5 MPa is too much force, note there is no smaller JSI bore, so you must reduce pressure; stepping up to the JSI40X500 yields 628 N. Since this is a 500 mm stroke, the Ø12 mm rod needs external guide support to prevent side-load bending. The air cushion only decelerates the piston near stroke end and will not hold a load if air is lost—install a pilot-operated check valve for vertical holding. Without the -S suffix, this unit cannot host magnetic sensors.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac JSI Series Standard Cylinder JSI32X500 FAQ
At 0.5 MPa it provides 402 N push and 345 N pull. At 0.7 MPa it provides 563 N push and 483 N pull. The theoretical maximum is 82 kgf at 1.0 MPa, and the air port size is G1/8.
The JSI is a JIS-standard profile cylinder that is shorter and more compact than an ISO 15552 cylinder of the same 32 mm bore, giving you a space saving without losing the 500 mm stroke.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC JSI Cylinders
Request a Quote for Airtac JSI Series Standard Cylinder JSI32X500
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.