Airtac JSI Series Standard Cylinder JSI32X655TC
The AirTAC Airtac JSI Series Standard Cylinder JSI32X655TC is a genuine double acting JIS-standard air cylinder with a Ø32mm bore and 655mm stroke, G1/8 air ports and adjustable end cushioning. Its no-tie-rod, hard-anodized profile barrel is more compact than an ISO 15552 cylinder of the same bore — a space-saver on tight machines.
- BoreØ32 mm
- Stroke655 mm
- Port sizeG1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 20 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac JSI Series Standard Cylinder JSI32X655TC
Delivering 402 N of push force at 0.5 MPa, this double-acting JIS-standard profile cylinder saves valuable machine space by being noticeably shorter than an ISO 15552 cylinder of the same 32 mm bore. The extruded hard-anodized aluminum barrel omits external rods to resist wear, while a two-way piston seal retains grease for a long, low-friction service life across the 655 mm stroke.
Because this specific SKU lacks the -S magnet, it cannot accept CMSE or DMSE position switches. For real-world sizing, plan for roughly 241 N of actual work at 0.5 MPa, which equates to lifting about 20 kg vertically with a 2:1 safety margin. The unit features a G1/8 port, an M10x1.25 rod thread, and adjustable 20 mm air cushions at both ends to smooth out deceleration.
Airtac JSI Series Standard Cylinder JSI32X655TC Technical Specifications
| Model | Airtac JSI Series Standard Cylinder JSI32X655TC |
|---|---|
| Series | JSI JIS-standard profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 655 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 20 mm |
| Max standard stroke | Up to 1000 mm |
Specifications follow the official AirTAC JSI (JIS standard) datasheet. Confirm against the product label before installation. Thread options: PT (blank) / G. Barrel: hard-anodized aluminum profile (no tie rods).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac JSI Series Standard Cylinder JSI32X655TC
| JSI | JIS-standard profile cylinder (double-acting type). |
|---|---|
| 32 | Bore size in mm (32 / 40 / 50 / 63 / 80 / 100 / 125). |
| ×655 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensors. |
JSI-family variants: JSI (double acting), JSID (double rod), JSIJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / TCM1 / TCM2. Thread PT (blank) / G.
Where the Airtac JSI Series Standard Cylinder JSI32X655TC Is Used
Long-Reach Pick & Place
Uses the 655 mm extension to transfer lightweight electronic components between conveyor lanes without requiring a gantry system.
Packaging Diverter
Pushes small cartons off a main packaging belt using 402 N of thrust, relying on the TC mount to pivot smoothly during the stroke.
Bin Extraction Arm
Extends deep into storage racking to pull tote bins, requiring external linear guides to support the 12 mm rod over the long travel distance.
Is the Airtac JSI Series Standard Cylinder JSI32X655TC the Right Cylinder?
When sizing this 32 mm bore, stepping up to the 40 mm bore increases the 0.5 MPa push force to 628 N, while there is no smaller JSI bore below 32 mm. The included TC trunnion mount provides a pivoting axis that accommodates slight misalignments, which is highly recommended given the 655 mm stroke. At this extended length, external guide rails should be used to prevent rod bending and absorb side loads. Remember that air loss or a centered valve will cause the piston to drift; the cushions only decelerate the stroke near the ends and do not act as a lock, so fit an external rod lock or pilot-operated check valve if the load must be held.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac JSI Series Standard Cylinder JSI32X655TC FAQ
This 32 mm bore cylinder has a G1/8 air port and an M10x1.25 rod thread. The thrust output is 402 N push and 345 N pull at 0.5 MPa, increasing to 563 N push and 483 N pull at 0.7 MPa. The theoretical maximum force is 82 kgf at 1.0 MPa.
No, because this specific SKU does not include the -S magnet option, it cannot accept CMSE or DMSE switches in the side grooves. You would need the -S variant to enable magnetic position sensing.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC JSI Cylinders
Request a Quote for Airtac JSI Series Standard Cylinder JSI32X655TC
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.