Airtac JSI Series Standard Cylinder JSI32X800S
The AirTAC Airtac JSI Series Standard Cylinder JSI32X800S is a genuine double acting JIS-standard air cylinder with a Ø32mm bore and 800mm stroke, G1/8 air ports and adjustable end cushioning. Its no-tie-rod, hard-anodized profile barrel is more compact than an ISO 15552 cylinder of the same bore — a space-saver on tight machines.
- BoreØ32 mm
- Stroke800 mm
- Port sizeG1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 20 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac JSI Series Standard Cylinder JSI32X800S
Generating 402 N of push force at 0.5 MPa, this double-acting 32 mm bore unit is a JIS-standard profile cylinder that is shorter and more compact than an ISO 15552 cylinder of the same bore. The extruded hard-anodized aluminum barrel omits external rods to resist wear, while the two-way piston seal retains grease for long, low-friction life. It operates at 30-800 mm/s and uses a G1/8 port.
Because the -S suffix equips the piston with a magnet, you can drop CMSE or DMSE reed and electronic switches directly into the side grooves for position sensing. Plan for about 241 N of real work at 0.5 MPa, which means it lifts roughly 20 kg vertically with a 2:1 safety margin. The 800 mm stroke is a long extension that requires careful external guidance to prevent rod bending under side loads.
Airtac JSI Series Standard Cylinder JSI32X800S Technical Specifications
| Model | Airtac JSI Series Standard Cylinder JSI32X800S |
|---|---|
| Series | JSI JIS-standard profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 800 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 20 mm |
| Max standard stroke | Up to 1000 mm |
Specifications follow the official AirTAC JSI (JIS standard) datasheet. Confirm against the product label before installation. Thread options: PT (blank) / G. Barrel: hard-anodized aluminum profile (no tie rods).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac JSI Series Standard Cylinder JSI32X800S
| JSI | JIS-standard profile cylinder (double-acting type). |
|---|---|
| 32 | Bore size in mm (32 / 40 / 50 / 63 / 80 / 100 / 125). |
| ×800 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensors. |
JSI-family variants: JSI (double acting), JSID (double rod), JSIJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / TCM1 / TCM2. Thread PT (blank) / G.
Where the Airtac JSI Series Standard Cylinder JSI32X800S Is Used
PCB Edge Routing
Traverses an 800 mm path to position PCB panels at a routing station, using the magnet for end-of-travel confirmation.
Small Tray Sorting
Pushes lightweight sorting trays along a conveyor line, where the compact profile saves valuable machine footprint.
Lab Sample Dispensing
Extends across a 800 mm work area to move low-friction lab sample racks, lifting roughly 20 kg loads vertically.
Is the Airtac JSI Series Standard Cylinder JSI32X800S the Right Cylinder?
If 402 N of push at 0.5 MPa is insufficient, stepping up to the JSI40X800S yields 628 N, while stepping down is not an option as 32 mm is the smallest JSI bore available. The M10x1.25 rod thread and 20 mm adjustable air cushions at both ends help manage end-of-stroke impact. For this 800 mm stroke, always use an external guide rail to support the load and prevent rod-bending forces. Remember that a plain cylinder drifts when air is lost or the valve is centered; the cushions only decelerate the piston near the ends and do not act as a lock. To hold a vertical load securely, install an external rod lock or a pilot-operated check valve.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac JSI Series Standard Cylinder JSI32X800S FAQ
At 0.5 MPa it provides 402 N push and 345 N pull. At 0.7 MPa it provides 563 N push and 483 N pull. The theoretical maximum force is 82 kgf at 1.0 MPa. It features a 32 mm bore, 800 mm stroke, G1/8 port, M10x1.25 rod thread, and operates at 30-800 mm/s.
It is a JIS-standard profile cylinder that is shorter and more compact than an ISO 15552 cylinder of the same 32 mm bore, saving space on tight machines. The -S suffix means it has a built-in magnet for CMSE/DMSE sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC JSI Cylinders
Request a Quote for Airtac JSI Series Standard Cylinder JSI32X800S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.