Airtac PB Pen-type Cylinder PB10X10RLB
The AirTAC Airtac PB Pen-type Cylinder PB10X10RLB is a double-acting pen-size (mini) air cylinder with a Ø10mm bore and 10mm stroke. Its slim round barrel and back cover are stainless steel, the M5×0.8 ports keep plumbing compact, and the fast, low-friction piston suits high-cycle small-part handling.
- BoreØ10 mm
- Stroke10 mm
- Port sizeM5×0.8
- Acting typeDouble acting
- Rod threadM8×1.0
- CushionElastic bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PB Pen-type Cylinder PB10X10RLB
The AirTAC PB10X10RLB is a double-acting JIS pen-size mini cylinder engineered for compact, high-frequency small-part motion. It features a slim SUS304 stainless steel round barrel and piston rod, offering excellent durability in damp or mildly corrosive environments while keeping end-of-arm tooling weight to an absolute minimum. Delivering 39.3 N of push force at 0.5 MPa, this 10 mm bore unit uses an M5x0.8 port and an M8x1.0 rod-end thread for straightforward load coupling.
This specific configuration includes an R axial air inlet for in-line plumbing and an LB mounting bracket to secure the body. The cylinder relies on a fixed TPU bumper at each end to decelerate the stroke over its 10 mm travel. Because the rod is a slender Ø4 mm, it is built for coaxial thrust rather than side loading, so maintaining alignment is critical for seal longevity.
Airtac PB Pen-type Cylinder PB10X10RLB Technical Specifications
| Model | Airtac PB Pen-type Cylinder PB10X10RLB |
|---|---|
| Series | PB JIS pen-size mini cylinder |
| Bore size | Ø10 mm |
| Rod diameter | Ø4 mm |
| Stroke | 10 mm |
| Acting type | Double acting |
| Port size | M5×0.8 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 0.7 MPa |
| Proof pressure | 1.2 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 50 – 800 mm/s |
| Cushion | Elastic bumper (both ends) |
| Max standard stroke | Up to 200 mm |
Specifications follow the official AirTAC PB pen-size datasheet. Piston rod and barrel are stainless steel. Confirm bore, stroke and back-cover option against the product label before installation.
Theoretical Output Force (Ø10mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 39.3 N | 33.0 N |
| 0.7 MPa (max) | 55.0 N | 46.2 N |
Values are taken from the AirTAC PB thrust table. Because pull acts on the rod-side annular area, pull force is always lower than push. Actual usable force is reduced by friction — size with a margin.
Model Code: Airtac PB Pen-type Cylinder PB10X10RLB
| PB | JIS pen-size double-acting mini-cylinder series. |
|---|---|
| 10 | Bore size in mm. |
| ×10 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| CB / U / R | Back cover: CB double clevis, U 90° side inlet, R axial inlet (bore-dependent). |
Mounting accessories: LB, FA, CJ. Related PB-family variants: PSB (single-acting push), PTB (single-acting pull), PBD (double rod), PBJ (adjustable stroke), PBR (front-mount).
Where the Airtac PB Pen-type Cylinder PB10X10RLB Is Used
PCB Pick-and-Place
Drives a tiny vacuum nozzle in electronics assembly, utilizing the short 10 mm stroke and slim body to fit densely populated pick-and-place heads without adding excessive mass.
Blister Pack Sealing
Actuates a small heat-seal jig in medical packaging lines, where the stainless barrel withstands routine washdowns and the LB bracket provides a rigid base for precise film alignment.
Lab Dispense Valve
Toggles a micro-dispense valve for reagent dosing, taking advantage of the 39.3 N extend force to puncture foil seals while the R axial inlet keeps pneumatic tubing neatly routed in a tight lab enclosure.
Is the Airtac PB Pen-type Cylinder PB10X10RLB the Right Cylinder?
When sizing this actuator, stepping down to the Ø6 bore yields 14.2 N of push at 0.5 MPa, whereas stepping up to the Ø12 bore provides 56.5 N. For the PB10X10RLB, plan for a safe working load of roughly 24 N (about 60% of the 39.3 N theoretical figure) to account for seal friction and smooth travel. In vertical lift scenarios, this equates to lifting about 2 kg safely with a 2:1 margin.
Remember that a standard double-acting cylinder does not hold its position if air pressure drops or the valve is centered; the piston will drift, and the fixed bumper only decelerates near the end of stroke rather than locking the load. To finalize your build, confirm the 10 mm bore, 10 mm stroke, M5x0.8 porting, R axial inlet, and LB mount requirement. No magnet is included in this code, so position sensing is not available without changing the model.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Slim pen body vs. a standard round cylinder
- ✓ Back cover: CB / U / R inlet direction
- ✓ Magnet (S) for sensors?
- ✓ Mounting: LB / FA / CJ or front thread
- ✓ Keep the load coaxial — avoid side load
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 0.7 MPa operating pressure.
- check Keep the load coaxial; avoid side load on the thin rod.
- check Do not dismantle the front or back cover.
- check Fit dust caps to ports during long-term storage.
- check Installation by qualified personnel per AirTAC docs.
Airtac PB Pen-type Cylinder PB10X10RLB FAQ
At 0.5 MPa, the push force is 39.3 N and the pull force is 33 N. At the maximum operating pressure of 0.7 MPa, the push force is 55 N and the pull force is 46.2 N. The operating pressure range is 0.15-0.7 MPa, with a speed of 50-800 mm/s.
It uses a fixed TPU bumper at each end that decelerates the piston over the last few millimeters; it is not adjustable and not a locking brake. If your application involves high cycling mass, meter-out the exhaust or add an external shock absorber. Additionally, it will not hold a load if air is lost, so an external rod lock is required for fail-safe holding.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC PB Pen-Size Cylinders
Request a Quote for Airtac PB Pen-type Cylinder PB10X10RLB
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.