Airtac PB Pen-type Cylinder PB10X120SR
The AirTAC Airtac PB Pen-type Cylinder PB10X120SR is a double-acting pen-size (mini) air cylinder with a Ø10mm bore and 120mm stroke. Its slim round barrel and back cover are stainless steel, the M5×0.8 ports keep plumbing compact, and the fast, low-friction piston suits high-cycle small-part handling.
- BoreØ10 mm
- Stroke120 mm
- Port sizeM5×0.8
- Acting typeDouble acting
- Rod threadM8×1.0
- CushionElastic bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PB Pen-type Cylinder PB10X120SR
The AirTAC PB10X120SR is a JIS pen-size double-acting single-rod mini cylinder engineered for compact, high-frequency motion. It delivers 39.3 N of push and 33 N of pull at 0.5 MPa, utilizing a slim SUS304 stainless steel barrel and a 4 mm rod to fit tight jigs and light end-of-arm tooling. The R suffix designates an axial air inlet for straightforward in-line plumbing.
This 10 mm bore unit features an M5x0.8 port and an M8x1.0 rod-end thread. Because it carries the S suffix, a built-in piston magnet enables position detection using AirTAC reed or electronic switches. Travel is capped by a fixed TPU bumper at each end that decelerates the piston over the final few millimeters; for higher velocity tooling mass, meter-out the exhaust or add an external shock absorber.
Airtac PB Pen-type Cylinder PB10X120SR Technical Specifications
| Model | Airtac PB Pen-type Cylinder PB10X120SR |
|---|---|
| Series | PB JIS pen-size mini cylinder |
| Bore size | Ø10 mm |
| Rod diameter | Ø4 mm |
| Stroke | 120 mm |
| Acting type | Double acting |
| Port size | M5×0.8 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 0.7 MPa |
| Proof pressure | 1.2 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 50 – 800 mm/s |
| Cushion | Elastic bumper (both ends) |
| Max standard stroke | Up to 200 mm |
Specifications follow the official AirTAC PB pen-size datasheet. Piston rod and barrel are stainless steel. Confirm bore, stroke and back-cover option against the product label before installation.
Theoretical Output Force (Ø10mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 39.3 N | 33.0 N |
| 0.7 MPa (max) | 55.0 N | 46.2 N |
Values are taken from the AirTAC PB thrust table. Because pull acts on the rod-side annular area, pull force is always lower than push. Actual usable force is reduced by friction — size with a margin.
Model Code: Airtac PB Pen-type Cylinder PB10X120SR
| PB | JIS pen-size double-acting mini-cylinder series. |
|---|---|
| 10 | Bore size in mm. |
| ×120 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| CB / U / R | Back cover: CB double clevis, U 90° side inlet, R axial inlet (bore-dependent). |
Mounting accessories: LB, FA, CJ. Related PB-family variants: PSB (single-acting push), PTB (single-acting pull), PBD (double rod), PBJ (adjustable stroke), PBR (front-mount).
Where the Airtac PB Pen-type Cylinder PB10X120SR Is Used
PCB Depaneling Router
Extends a light cutting probe to singulate printed circuit boards, where the 39.3 N push force is sufficient for routing and the pen-size body clears adjacent fixturing.
Lab Dispenser Head
Drives a micro-valve for precise chemical reagent dosing, using the S magnet to trigger an electronic switch at the exact 120 mm stroke end.
Pick-and-Place Ejector
Kicks small electronic components from a vacuum nozzle, fitting within the tight envelope of a pick-and-place head while relying on the fixed TPU bumper to soften the impact.
Is the Airtac PB Pen-type Cylinder PB10X120SR the Right Cylinder?
When sizing this actuator, stepping down to the 6 mm bore yields 14.2 N push, while stepping up to the 12 mm bore provides 56.5 N push at 0.5 MPa. Plan for a safe working load of roughly 24 N (about 60% of the 39.3 N theoretical figure) to account for seal friction and smooth travel. Vertically, this equates to lifting about 2 kg with a sane 2:1 safety margin. To finalize your order, confirm the 10 mm bore, 120 mm stroke, M5x0.8 port, S magnet, and R axial inlet. Note that a plain PB body does not hold its load if air pressure drops or the valve centers; the piston will drift, so an external rod lock is required for fail-safe positioning.
The 4 mm rod is designed strictly for coaxial thrust. Over this 120 mm stroke, any off-axis load risks bending the slender rod, so incorporate an external linear bearing guide to prevent side loading.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Slim pen body vs. a standard round cylinder
- ✓ Back cover: CB / U / R inlet direction
- ✓ Magnet (S) for sensors?
- ✓ Mounting: LB / FA / CJ or front thread
- ✓ Keep the load coaxial — avoid side load
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 0.7 MPa operating pressure.
- check Keep the load coaxial; avoid side load on the thin rod.
- check Do not dismantle the front or back cover.
- check Fit dust caps to ports during long-term storage.
- check Installation by qualified personnel per AirTAC docs.
Airtac PB Pen-type Cylinder PB10X120SR FAQ
At 0.5 MPa, this double-acting cylinder provides 39.3 N push and 33 N pull. At the maximum operating pressure of 0.7 MPa, it yields 55 N push and 46.2 N pull. It operates on filtered air between 0.15 and 0.7 MPa at speeds of 50-800 mm/s.
The R suffix indicates an axial air inlet for in-line plumbing, keeping the footprint narrow. The S suffix means the piston contains a magnet compatible with AirTAC reed or electronic switches for position feedback. The SUS304 stainless barrel and covers protect the unit in mildly damp environments.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC PB Pen-Size Cylinders
Request a Quote for Airtac PB Pen-type Cylinder PB10X120SR
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.