Airtac PB Pen-type Cylinder PB10X125SUFA
The AirTAC Airtac PB Pen-type Cylinder PB10X125SUFA is a double-acting pen-size (mini) air cylinder with a Ø10mm bore and 125mm stroke. Its slim round barrel and back cover are stainless steel, the M5×0.8 ports keep plumbing compact, and the fast, low-friction piston suits high-cycle small-part handling.
- BoreØ10 mm
- Stroke125 mm
- Port sizeM5×0.8
- Acting typeDouble acting
- Rod threadM8×1.0
- CushionElastic bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PB Pen-type Cylinder PB10X125SUFA
The AirTAC PB10X125SUFA is a double-acting JIS pen-size mini cylinder engineered for compact automation. It delivers 39.3 N of push and 33 N of pull at 0.5 MPa, utilizing a slim SUS304 stainless steel barrel and a 4 mm rod to fit tight jig spaces. Plumbing is simplified via the U 90-degree side air inlet, while the FA bracket provides a robust mounting interface.
This model includes a built-in S magnet for position detection using AirTAC reed or electronic switches. Deceleration relies on a fixed TPU bumper at each end rather than an adjustable air cushion. Because the bumper only absorbs energy over the final few millimeters, high-speed cycles with real tooling mass require metering out the exhaust or adding an external shock absorber.
Airtac PB Pen-type Cylinder PB10X125SUFA Technical Specifications
| Model | Airtac PB Pen-type Cylinder PB10X125SUFA |
|---|---|
| Series | PB JIS pen-size mini cylinder |
| Bore size | Ø10 mm |
| Rod diameter | Ø4 mm |
| Stroke | 125 mm |
| Acting type | Double acting |
| Port size | M5×0.8 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 0.7 MPa |
| Proof pressure | 1.2 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 50 – 800 mm/s |
| Cushion | Elastic bumper (both ends) |
| Max standard stroke | Up to 200 mm |
Specifications follow the official AirTAC PB pen-size datasheet. Piston rod and barrel are stainless steel. Confirm bore, stroke and back-cover option against the product label before installation.
Theoretical Output Force (Ø10mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 39.3 N | 33.0 N |
| 0.7 MPa (max) | 55.0 N | 46.2 N |
Values are taken from the AirTAC PB thrust table. Because pull acts on the rod-side annular area, pull force is always lower than push. Actual usable force is reduced by friction — size with a margin.
Model Code: Airtac PB Pen-type Cylinder PB10X125SUFA
| PB | JIS pen-size double-acting mini-cylinder series. |
|---|---|
| 10 | Bore size in mm. |
| ×125 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| CB / U / R | Back cover: CB double clevis, U 90° side inlet, R axial inlet (bore-dependent). |
Mounting accessories: LB, FA, CJ. Related PB-family variants: PSB (single-acting push), PTB (single-acting pull), PBD (double rod), PBJ (adjustable stroke), PBR (front-mount).
Where the Airtac PB Pen-type Cylinder PB10X125SUFA Is Used
PCB Depaneling Routing
Advances a high-speed router bit along a 125 mm path to singulate circuit boards, utilizing the slim stainless body to fit between dense tooling carriages.
Filler Nozzle Alignment
Pivots a small fluid nozzle into position over pouches using the FA bracket, depending on the U inlet for flat hose routing in cramped packaging cells.
Lab Sample Ejection
Pushes lightweight vial racks out of a testing carousel, where the S magnet confirms ejection via a solid-state switch before the dial index moves.
Is the Airtac PB Pen-type Cylinder PB10X125SUFA the Right Cylinder?
Selecting this 10 mm bore offers a middle ground: step down to a 6 mm bore for 14.2 N push at 0.5 MPa, or up to a 12 mm bore for 56.5 N push. For this specific unit, plan for a safe working load of roughly 24 N (about 60% of the 0.5 MPa theoretical force) to account for seal friction. In vertical lifts, this translates to safely raising about 2 kg with a 2:1 margin.
With a 125 mm stroke on a thin 4 mm rod, maintaining coaxial thrust is critical; add an external linear bearing if the load is off-axis. Confirm your ordering essentials: 10 mm bore, 125 mm stroke, M5x0.8 port, S magnet, U side inlet, and FA mount. Note that a plain PB body drifts if air pressure is lost, so install an external rod lock if the application requires fail-safe load holding.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Slim pen body vs. a standard round cylinder
- ✓ Back cover: CB / U / R inlet direction
- ✓ Magnet (S) for sensors?
- ✓ Mounting: LB / FA / CJ or front thread
- ✓ Keep the load coaxial — avoid side load
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 0.7 MPa operating pressure.
- check Keep the load coaxial; avoid side load on the thin rod.
- check Do not dismantle the front or back cover.
- check Fit dust caps to ports during long-term storage.
- check Installation by qualified personnel per AirTAC docs.
Airtac PB Pen-type Cylinder PB10X125SUFA FAQ
At 0.5 MPa, the push force is 39.3 N and the pull force is 33 N. At the maximum operating pressure of 0.7 MPa, the push is 55 N and the pull is 46.2 N. The operating pressure range is 0.15-0.7 MPa, with a speed of 50-800 mm/s.
It uses a fixed TPU bumper at each end to decelerate the piston over the last few millimeters, which is not adjustable or field-tunable. The included S magnet allows AirTAC reed or electronic switches to detect piston position. For heavy tooling at high speeds, external shock absorption is recommended.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC PB Pen-Size Cylinders
Request a Quote for Airtac PB Pen-type Cylinder PB10X125SUFA
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.