Airtac PB Pen-type Cylinder PB10X20U
The AirTAC Airtac PB Pen-type Cylinder PB10X20U is a double-acting pen-size (mini) air cylinder with a Ø10mm bore and 20mm stroke. Its slim round barrel and back cover are stainless steel, the M5×0.8 ports keep plumbing compact, and the fast, low-friction piston suits high-cycle small-part handling.
- BoreØ10 mm
- Stroke20 mm
- Port sizeM5×0.8
- Acting typeDouble acting
- Rod threadM8×1.0
- CushionElastic bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PB Pen-type Cylinder PB10X20U
The AirTAC PB10X20U is a double-acting JIS pen-size mini cylinder engineered for compact, high-frequency small-part motion. It generates 39.3 N of push and 33 N of pull at 0.5 MPa, utilizing a 10 mm bore and a 20 mm stroke. The U option designates a 90-degree side air inlet, allowing flat plumbing in confined spaces. Its slim round SUS304 stainless barrel and piston rod provide reliable durability in damp or mildly corrosive environments.
Air enters via an M5x0.8 port to drive the 4 mm rod, which features an M8x1.0 rod-end thread for secure load coupling. Operating speeds reach 50-800 mm/s, with a fixed TPU bumper at each end to absorb impact. Because the bumper only decelerates the final few millimeters of travel, high-speed cycles with real tooling mass require metering out the exhaust or adding an external shock absorber.
Airtac PB Pen-type Cylinder PB10X20U Technical Specifications
| Model | Airtac PB Pen-type Cylinder PB10X20U |
|---|---|
| Series | PB JIS pen-size mini cylinder |
| Bore size | Ø10 mm |
| Rod diameter | Ø4 mm |
| Stroke | 20 mm |
| Acting type | Double acting |
| Port size | M5×0.8 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 0.7 MPa |
| Proof pressure | 1.2 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 50 – 800 mm/s |
| Cushion | Elastic bumper (both ends) |
| Max standard stroke | Up to 200 mm |
Specifications follow the official AirTAC PB pen-size datasheet. Piston rod and barrel are stainless steel. Confirm bore, stroke and back-cover option against the product label before installation.
Theoretical Output Force (Ø10mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 39.3 N | 33.0 N |
| 0.7 MPa (max) | 55.0 N | 46.2 N |
Values are taken from the AirTAC PB thrust table. Because pull acts on the rod-side annular area, pull force is always lower than push. Actual usable force is reduced by friction — size with a margin.
Model Code: Airtac PB Pen-type Cylinder PB10X20U
| PB | JIS pen-size double-acting mini-cylinder series. |
|---|---|
| 10 | Bore size in mm. |
| ×20 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| CB / U / R | Back cover: CB double clevis, U 90° side inlet, R axial inlet (bore-dependent). |
Mounting accessories: LB, FA, CJ. Related PB-family variants: PSB (single-acting push), PTB (single-acting pull), PBD (double rod), PBJ (adjustable stroke), PBR (front-mount).
Where the Airtac PB Pen-type Cylinder PB10X20U Is Used
PCB Depaneling Jig
Actuates a small cutting blade or clamping finger in a tight electronics assembly fixture where the 90-degree side inlet keeps plumbing flush against the machine frame.
Label Applicator Tamp
Provides a short 20 mm stroke to press adhesive labels onto lightweight cartons, utilizing the 39.3 N push force without crushing the packaging material.
Lab Sample Ejector
Ejects small vials from a testing carousel in a humid laboratory environment, relying on the SUS304 stainless build to resist moisture and chemical exposure.
Is the Airtac PB Pen-type Cylinder PB10X20U the Right Cylinder?
When sizing this actuator, plan for a safe working load of roughly 24 N, which is about 60 percent of the 39.3 N theoretical push at 0.5 MPa. This equates to lifting approximately 2 kg vertically with a sane 2:1 safety margin. If your application requires less force, stepping down to the 6 mm bore yields 14.2 N of push, while stepping up to the 12 mm bore provides 56.5 N at the same pressure.
Note that a plain PB body does not hold its position if air pressure drops or the valve is centered; the piston will drift, so an external stop or rod lock is required for fail-safe holding. The thin 4 mm rod is built for coaxial thrust, so avoid side loading or add a linear bearing for off-axis guidance. To order, confirm the 10 mm bore, 20 mm stroke, M5x0.8 porting, the U 90-degree side inlet, and your desired mounting bracket.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Slim pen body vs. a standard round cylinder
- ✓ Back cover: CB / U / R inlet direction
- ✓ Magnet (S) for sensors?
- ✓ Mounting: LB / FA / CJ or front thread
- ✓ Keep the load coaxial — avoid side load
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 0.7 MPa operating pressure.
- check Keep the load coaxial; avoid side load on the thin rod.
- check Do not dismantle the front or back cover.
- check Fit dust caps to ports during long-term storage.
- check Installation by qualified personnel per AirTAC docs.
Airtac PB Pen-type Cylinder PB10X20U FAQ
At 0.5 MPa, the push force is 39.3 N and the pull force is 33 N. At the maximum operating pressure of 0.7 MPa, the push is 55 N and the pull is 46.2 N. The operating pressure range is 0.15-0.7 MPa, with a proof pressure of 1.2 MPa and a speed range of 50-800 mm/s.
No, the piston will drift if air is lost or the valve is centered. The fixed TPU bumper at each end only decelerates the rod near the stroke ends and does not act as a lock or brake. For vertical load holding, you must install an external stop or rod lock.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC PB Pen-Size Cylinders
Request a Quote for Airtac PB Pen-type Cylinder PB10X20U
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.