Airtac PB Pen-type Cylinder PB10X30U
The AirTAC Airtac PB Pen-type Cylinder PB10X30U is a double-acting pen-size (mini) air cylinder with a Ø10mm bore and 30mm stroke. Its slim round barrel and back cover are stainless steel, the M5×0.8 ports keep plumbing compact, and the fast, low-friction piston suits high-cycle small-part handling.
- BoreØ10 mm
- Stroke30 mm
- Port sizeM5×0.8
- Acting typeDouble acting
- Rod threadM8×1.0
- CushionElastic bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PB Pen-type Cylinder PB10X30U
The AirTAC PB10X30U is a JIS pen-size double-acting single-rod mini cylinder engineered for compact automation. It delivers 39.3 N of push force at 0.5 MPa, utilizing a 10 mm bore and a 30 mm stroke. The U suffix specifies a 90-degree perpendicular side air inlet, allowing flat plumbing along the machine frame where an axial port would protrude. With an M5x0.8 port and an M8x1.0 rod-end thread, it integrates seamlessly into tight jigs.
Constructed with a SUS304 stainless steel piston rod and barrel, this unit withstands damp or mildly corrosive environments. It relies on a fixed TPU bumper at each end to decelerate motion over the final few millimeters, rather than an adjustable air cushion. Because the slender 4 mm rod is designed purely for coaxial thrust, operators should avoid side loading and add an external guide for off-axis forces.
Airtac PB Pen-type Cylinder PB10X30U Technical Specifications
| Model | Airtac PB Pen-type Cylinder PB10X30U |
|---|---|
| Series | PB JIS pen-size mini cylinder |
| Bore size | Ø10 mm |
| Rod diameter | Ø4 mm |
| Stroke | 30 mm |
| Acting type | Double acting |
| Port size | M5×0.8 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 0.7 MPa |
| Proof pressure | 1.2 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 50 – 800 mm/s |
| Cushion | Elastic bumper (both ends) |
| Max standard stroke | Up to 200 mm |
Specifications follow the official AirTAC PB pen-size datasheet. Piston rod and barrel are stainless steel. Confirm bore, stroke and back-cover option against the product label before installation.
Theoretical Output Force (Ø10mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 39.3 N | 33.0 N |
| 0.7 MPa (max) | 55.0 N | 46.2 N |
Values are taken from the AirTAC PB thrust table. Because pull acts on the rod-side annular area, pull force is always lower than push. Actual usable force is reduced by friction — size with a margin.
Model Code: Airtac PB Pen-type Cylinder PB10X30U
| PB | JIS pen-size double-acting mini-cylinder series. |
|---|---|
| 10 | Bore size in mm. |
| ×30 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| CB / U / R | Back cover: CB double clevis, U 90° side inlet, R axial inlet (bore-dependent). |
Mounting accessories: LB, FA, CJ. Related PB-family variants: PSB (single-acting push), PTB (single-acting pull), PBD (double rod), PBJ (adjustable stroke), PBR (front-mount).
Where the Airtac PB Pen-type Cylinder PB10X30U Is Used
PCB Depaneling Jig
Actuates a small cutting blade on a depaneling router, using the 90-degree side inlet to keep plumbing flush against the tight routing head.
Blister Pack Sealing
Provides the 39.3 N push at 0.5 MPa needed to clamp thin film heating dies in a packaging line without deforming the product.
Pick-and-Place Ejector
Ejects small electronic components from vacuum tooling at high frequency, benefiting from the 50-800 mm/s speed range and slim stainless body.
Is the Airtac PB Pen-type Cylinder PB10X30U the Right Cylinder?
When sizing this actuator, stepping down to the 6 mm bore yields 14.2 N push at 0.5 MPa, while stepping up to the 12 mm bore provides 56.5 N. For the PB10X30U, plan for a safe working load of roughly 24 N at 0.5 MPa, which equates to lifting about 2 kg vertically with a 2:1 safety margin. Note that this cylinder does not hold its position if air pressure drops or the valve centers; the piston will drift, requiring an external stop or rod lock for fail-safe holding.
To finalize your order, confirm the 10 mm bore, 30 mm stroke, M5x0.8 port, and the U-type 90-degree side inlet. This configuration ships without a sensor magnet, and mounting requires optional LB, FA, or CJ brackets.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Slim pen body vs. a standard round cylinder
- ✓ Back cover: CB / U / R inlet direction
- ✓ Magnet (S) for sensors?
- ✓ Mounting: LB / FA / CJ or front thread
- ✓ Keep the load coaxial — avoid side load
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 0.7 MPa operating pressure.
- check Keep the load coaxial; avoid side load on the thin rod.
- check Do not dismantle the front or back cover.
- check Fit dust caps to ports during long-term storage.
- check Installation by qualified personnel per AirTAC docs.
Airtac PB Pen-type Cylinder PB10X30U FAQ
At 0.5 MPa, the push force is 39.3 N and the pull force is 33 N. At the maximum operating pressure of 0.7 MPa, the push force is 55 N and the pull force is 46.2 N. The operating pressure range is 0.15-0.7 MPa, with a speed of 50-800 mm/s.
The U suffix denotes a 90-degree perpendicular side air inlet for flat plumbing in confined spaces. The cylinder uses a fixed TPU bumper at each end to decelerate motion, which is not adjustable. If operating at high speeds with real tooling mass, you should meter-out the exhaust or add an external shock absorber.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC PB Pen-Size Cylinders
Request a Quote for Airtac PB Pen-type Cylinder PB10X30U
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.