Airtac PB Pen-type Cylinder PB10X35SCB
The AirTAC Airtac PB Pen-type Cylinder PB10X35SCB is a double-acting pen-size (mini) air cylinder with a Ø10mm bore and 35mm stroke. Its slim round barrel and back cover are stainless steel, the M5×0.8 ports keep plumbing compact, and the fast, low-friction piston suits high-cycle small-part handling.
- BoreØ10 mm
- Stroke35 mm
- Port sizeM5×0.8
- Acting typeDouble acting
- Rod threadM8×1.0
- CushionElastic bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PB Pen-type Cylinder PB10X35SCB
The AirTAC PB10X35SCB is a JIS double-acting single-rod pen-size mini cylinder engineered for compact, high-frequency motion. It delivers a theoretical push of 39.3 N and pull of 33 N at 0.5 MPa, driven through an M5x0.8 air port. The slim SUS304 stainless round barrel and screwed-in covers provide excellent durability in damp or mildly corrosive environments while saving critical space on light end-of-arm tooling.
This specific configuration includes a built-in piston magnet (S) for position detection using AirTAC reed or electronic switches, and a CB double clevis back cover for pivoting loads. Travel is capped by a fixed TPU bumper at each end that absorbs impact over the final few millimeters. Because the 4 mm rod is designed strictly for coaxial thrust, adding an external guide is recommended if side loads are present.
Airtac PB Pen-type Cylinder PB10X35SCB Technical Specifications
| Model | Airtac PB Pen-type Cylinder PB10X35SCB |
|---|---|
| Series | PB JIS pen-size mini cylinder |
| Bore size | Ø10 mm |
| Rod diameter | Ø4 mm |
| Stroke | 35 mm |
| Acting type | Double acting |
| Port size | M5×0.8 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 0.7 MPa |
| Proof pressure | 1.2 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 50 – 800 mm/s |
| Cushion | Elastic bumper (both ends) |
| Max standard stroke | Up to 200 mm |
Specifications follow the official AirTAC PB pen-size datasheet. Piston rod and barrel are stainless steel. Confirm bore, stroke and back-cover option against the product label before installation.
Theoretical Output Force (Ø10mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 39.3 N | 33.0 N |
| 0.7 MPa (max) | 55.0 N | 46.2 N |
Values are taken from the AirTAC PB thrust table. Because pull acts on the rod-side annular area, pull force is always lower than push. Actual usable force is reduced by friction — size with a margin.
Model Code: Airtac PB Pen-type Cylinder PB10X35SCB
| PB | JIS pen-size double-acting mini-cylinder series. |
|---|---|
| 10 | Bore size in mm. |
| ×35 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| CB / U / R | Back cover: CB double clevis, U 90° side inlet, R axial inlet (bore-dependent). |
Mounting accessories: LB, FA, CJ. Related PB-family variants: PSB (single-acting push), PTB (single-acting pull), PBD (double rod), PBJ (adjustable stroke), PBR (front-mount).
Where the Airtac PB Pen-type Cylinder PB10X35SCB Is Used
PCB Depaneling Jig
Actuates a small cutting blade or clamping finger in tight electronics assembly cells where the slim 10 mm barrel prevents collision with adjacent tooling.
Pouch Flap Tucking
Pushes carton flaps or thin packaging films at high speed, relying on the fixed TPU bumper to soften the stroke end without requiring bulky external cushions.
Lab Sample Diverting
Pivots a small guide chute on a fluid analysis carousel using the CB double clevis, with the S magnet triggering a solid-state switch to confirm gate position.
Is the Airtac PB Pen-type Cylinder PB10X35SCB the Right Cylinder?
When sizing this actuator, plan for a safe working load of roughly 24 N at 0.5 MPa, which accounts for seal friction and smooth travel. For vertical lifting, this equates to handling a part mass of about 2 kg with a standard 2:1 safety margin. If your application requires slightly less force, the adjacent Ø6 bore provides 14.2 N of push at 0.5 MPa; stepping up to the Ø12 bore yields 56.5 N. Note that a standard PB body drifts when air pressure is lost or the valve is centered, so an external rod lock is necessary for fail-safe holding.
Confirm your ordering essentials to match this exact unit: 10 mm bore, 35 mm stroke, M5x0.8 port, S magnet for sensing, and CB double clevis mounting. The maximum standard stroke available for this bore is 200 mm, and operating pressure must stay between 0.15 and 0.7 MPa.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Slim pen body vs. a standard round cylinder
- ✓ Back cover: CB / U / R inlet direction
- ✓ Magnet (S) for sensors?
- ✓ Mounting: LB / FA / CJ or front thread
- ✓ Keep the load coaxial — avoid side load
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 0.7 MPa operating pressure.
- check Keep the load coaxial; avoid side load on the thin rod.
- check Do not dismantle the front or back cover.
- check Fit dust caps to ports during long-term storage.
- check Installation by qualified personnel per AirTAC docs.
Airtac PB Pen-type Cylinder PB10X35SCB FAQ
At 0.5 MPa this 10 mm bore cylinder exerts 39.3 N of push (extend) and 33 N of pull (retract). At the maximum operating pressure of 0.7 MPa, the push is 55 N and the pull is 46.2 N. The operating pressure range is 0.15-0.7 MPa, with a proof pressure of 1.2 MPa and a speed range of 50-800 mm/s.
The CB back cover provides a double clevis joint that allows the cylinder to pivot smoothly with the load path. End-of-stroke energy is managed by a fixed TPU bumper at each end, which decelerates the piston over the final few millimeters. It is not an adjustable air cushion or a locking device, so high-speed pivoting masses may require metering the exhaust or adding an external shock absorber.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC PB Pen-Size Cylinders
Request a Quote for Airtac PB Pen-type Cylinder PB10X35SCB
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.