Airtac PB Pen-type Cylinder PB10X5CB
The AirTAC Airtac PB Pen-type Cylinder PB10X5CB is a double-acting pen-size (mini) air cylinder with a Ø10mm bore and 5mm stroke. Its slim round barrel and back cover are stainless steel, the M5×0.8 ports keep plumbing compact, and the fast, low-friction piston suits high-cycle small-part handling.
- BoreØ10 mm
- Stroke5 mm
- Port sizeM5×0.8
- Acting typeDouble acting
- Rod threadM8×1.0
- CushionElastic bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PB Pen-type Cylinder PB10X5CB
The AirTAC PB10X5CB is a JIS pen-size double-acting mini cylinder engineered for short 5mm strokes. It produces 39.3 N of push and 33 N of pull at 0.5 MPa, utilizing a slim SUS304 stainless steel barrel and a 4mm rod with an M8x1.0 end thread. This compact profile saves valuable space and payload on light end-of-arm tooling where larger bodies cannot fit.
Air enters via an M5x0.8 port, and the CB double clevis back cover allows the body to pivot smoothly with the load. Deceleration relies on a fixed TPU bumper at each end rather than an adjustable air cushion. Because the bumper only absorbs energy over the final few millimeters, high-speed cycling with heavy tooling requires metering out the exhaust or adding an external shock absorber.
Airtac PB Pen-type Cylinder PB10X5CB Technical Specifications
| Model | Airtac PB Pen-type Cylinder PB10X5CB |
|---|---|
| Series | PB JIS pen-size mini cylinder |
| Bore size | Ø10 mm |
| Rod diameter | Ø4 mm |
| Stroke | 5 mm |
| Acting type | Double acting |
| Port size | M5×0.8 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 0.7 MPa |
| Proof pressure | 1.2 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 50 – 800 mm/s |
| Cushion | Elastic bumper (both ends) |
| Max standard stroke | Up to 200 mm |
Specifications follow the official AirTAC PB pen-size datasheet. Piston rod and barrel are stainless steel. Confirm bore, stroke and back-cover option against the product label before installation.
Theoretical Output Force (Ø10mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 39.3 N | 33.0 N |
| 0.7 MPa (max) | 55.0 N | 46.2 N |
Values are taken from the AirTAC PB thrust table. Because pull acts on the rod-side annular area, pull force is always lower than push. Actual usable force is reduced by friction — size with a margin.
Model Code: Airtac PB Pen-type Cylinder PB10X5CB
| PB | JIS pen-size double-acting mini-cylinder series. |
|---|---|
| 10 | Bore size in mm. |
| ×5 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| CB / U / R | Back cover: CB double clevis, U 90° side inlet, R axial inlet (bore-dependent). |
Mounting accessories: LB, FA, CJ. Related PB-family variants: PSB (single-acting push), PTB (single-acting pull), PBD (double rod), PBJ (adjustable stroke), PBR (front-mount).
Where the Airtac PB Pen-type Cylinder PB10X5CB Is Used
PCB Connector Insertion
Drives a 5mm precise downward push to seat delicate electronic headers onto circuit boards without damaging surrounding SMD components.
Pouch Tab Tucking
Executes a short, repetitive folding motion to tuck adhesive tabs on thin film packaging prior to heat sealing.
Diverter Gate Pivot
Pairs with the CB clevis to swing a lightweight sorting flap on a conveyor, briefly nudging small plastic parts into a secondary lane.
Is the Airtac PB Pen-type Cylinder PB10X5CB the Right Cylinder?
When sizing this 10mm bore actuator, stepping down to a 6mm bore yields 14.2 N of push, while stepping up to a 12mm bore provides 56.5 N at 0.5 MPa. For this specific CB clevis model, plan for a safe working load of roughly 24 N, which is about 60% of the 0.5 MPa theoretical force to account for seal friction. You can also estimate a 2 kg vertical lift with a 2:1 safety margin.
To finalize your order, confirm the 10mm bore, 5mm stroke, M5x0.8 porting, and the CB double clevis option. Note that a plain PB cylinder drifts when air pressure is lost or the valve is centered, as the bumpers only decelerate near stroke end and do not function as a locking mechanism. If your process requires fail-safe position holding, specify an external rod lock.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Slim pen body vs. a standard round cylinder
- ✓ Back cover: CB / U / R inlet direction
- ✓ Magnet (S) for sensors?
- ✓ Mounting: LB / FA / CJ or front thread
- ✓ Keep the load coaxial — avoid side load
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 0.7 MPa operating pressure.
- check Keep the load coaxial; avoid side load on the thin rod.
- check Do not dismantle the front or back cover.
- check Fit dust caps to ports during long-term storage.
- check Installation by qualified personnel per AirTAC docs.
Airtac PB Pen-type Cylinder PB10X5CB FAQ
At 0.5 MPa, the push force is 39.3 N and the pull force is 33 N. At the maximum operating pressure of 0.7 MPa, the push force is 55 N and the pull force is 46.2 N.
No, the piston will drift if air is lost or the valve is centered. The fixed TPU bumpers only decelerate the rod near the stroke ends and do not act as a brake. An external stop or rod lock is required for fail-safe load holding.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC PB Pen-Size Cylinders
Request a Quote for Airtac PB Pen-type Cylinder PB10X5CB
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.