Airtac PB Pen-type Cylinder PB10X75R
The AirTAC Airtac PB Pen-type Cylinder PB10X75R is a double-acting pen-size (mini) air cylinder with a Ø10mm bore and 75mm stroke. Its slim round barrel and back cover are stainless steel, the M5×0.8 ports keep plumbing compact, and the fast, low-friction piston suits high-cycle small-part handling.
- BoreØ10 mm
- Stroke75 mm
- Port sizeM5×0.8
- Acting typeDouble acting
- Rod threadM8×1.0
- CushionElastic bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PB Pen-type Cylinder PB10X75R
The AirTAC PB10X75R is a double-acting JIS pen-size mini cylinder engineered for compact, high-frequency small-part motion. It features a slim SUS304 stainless steel barrel and piston rod, offering reliable durability in damp or mildly corrosive environments. Delivering 39.3 N of push force at 0.5 MPa, it uses an M5x0.8 port and an M8x1.0 rod-end thread to drive light tooling.
This 75 mm stroke variant includes an R axial air inlet for straightforward in-line plumbing. To manage impact energy, a fixed TPU bumper sits at each end to decelerate the piston over the final few millimeters. Because the rod is only 4 mm thick, it is built for coaxial thrust rather than side loading, so keeping the load guided ensures smooth travel across the full extension.
Airtac PB Pen-type Cylinder PB10X75R Technical Specifications
| Model | Airtac PB Pen-type Cylinder PB10X75R |
|---|---|
| Series | PB JIS pen-size mini cylinder |
| Bore size | Ø10 mm |
| Rod diameter | Ø4 mm |
| Stroke | 75 mm |
| Acting type | Double acting |
| Port size | M5×0.8 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 0.7 MPa |
| Proof pressure | 1.2 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 50 – 800 mm/s |
| Cushion | Elastic bumper (both ends) |
| Max standard stroke | Up to 200 mm |
Specifications follow the official AirTAC PB pen-size datasheet. Piston rod and barrel are stainless steel. Confirm bore, stroke and back-cover option against the product label before installation.
Theoretical Output Force (Ø10mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 39.3 N | 33.0 N |
| 0.7 MPa (max) | 55.0 N | 46.2 N |
Values are taken from the AirTAC PB thrust table. Because pull acts on the rod-side annular area, pull force is always lower than push. Actual usable force is reduced by friction — size with a margin.
Model Code: Airtac PB Pen-type Cylinder PB10X75R
| PB | JIS pen-size double-acting mini-cylinder series. |
|---|---|
| 10 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| CB / U / R | Back cover: CB double clevis, U 90° side inlet, R axial inlet (bore-dependent). |
Mounting accessories: LB, FA, CJ. Related PB-family variants: PSB (single-acting push), PTB (single-acting pull), PBD (double rod), PBJ (adjustable stroke), PBR (front-mount).
Where the Airtac PB Pen-type Cylinder PB10X75R Is Used
PCB Depaneling Jig
Actuates a light cutting blade on an electronic assembly line, utilizing the 39.3 N push force and 75 mm stroke to separate routed circuit boards cleanly.
Carton Flap Folder
Tucks small corrugated flaps on a packaging conveyor, where the compact pen-size body fits neatly between upper guide rails without collision.
Lab Sample Ejector
Pushes prepared vials out of a testing carousel, relying on the SUS304 stainless construction to withstand frequent wipe-downs and humid laboratory conditions.
Is the Airtac PB Pen-type Cylinder PB10X75R the Right Cylinder?
When sizing this actuator, plan for a safe working load of about 24 N, which is roughly 60 percent of the 39.3 N theoretical push at 0.5 MPa, leaving margin for seal friction. For vertical lifts, this equates to raising approximately 2 kg safely with a 2:1 factor. If your task requires slightly less force, the neighbouring Ø6 bore provides 14.2 N of push at 0.5 MPa; stepping up to the Ø12 bore yields 56.5 N. Note that a plain PB body does not hold position if air pressure drops or the valve centers, so an external rod lock is needed for fail-safe holding.
To order, confirm the 10 mm bore, 75 mm stroke, M5x0.8 porting, and the R axial inlet configuration. This unit ships without a sensor magnet, so position detection requires external methods. If your tooling mass is high, meter-out the exhaust or add an external shock absorber since the fixed bumpers are not adjustable.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Slim pen body vs. a standard round cylinder
- ✓ Back cover: CB / U / R inlet direction
- ✓ Magnet (S) for sensors?
- ✓ Mounting: LB / FA / CJ or front thread
- ✓ Keep the load coaxial — avoid side load
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 0.7 MPa operating pressure.
- check Keep the load coaxial; avoid side load on the thin rod.
- check Do not dismantle the front or back cover.
- check Fit dust caps to ports during long-term storage.
- check Installation by qualified personnel per AirTAC docs.
Airtac PB Pen-type Cylinder PB10X75R FAQ
At 0.5 MPa, the push force is 39.3 N and the pull force is 33 N. At the maximum operating pressure of 0.7 MPa, the push force is 55 N and the pull force is 46.2 N. The operating pressure range is 0.15-0.7 MPa, with a speed of 50-800 mm/s.
The R designation means it has an axial air inlet for in-line plumbing straight into the back cover. It uses a fixed TPU bumper at each end to decelerate the piston near the stroke limits, but this is not an adjustable air cushion or a locking brake. If operating at high speed with significant tooling mass, you should meter-out the exhaust or add an external shock absorber.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC PB Pen-Size Cylinders
Request a Quote for Airtac PB Pen-type Cylinder PB10X75R
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.