Airtac PB Pen-type Cylinder PB6X60R
The AirTAC Airtac PB Pen-type Cylinder PB6X60R is a double-acting pen-size (mini) air cylinder with a Ø6mm bore and 60mm stroke. Its slim round barrel and back cover are stainless steel, the M5×0.8 ports keep plumbing compact, and the fast, low-friction piston suits high-cycle small-part handling.
- BoreØ6 mm
- Stroke60 mm
- Port sizeM5×0.8
- Acting typeDouble acting
- Rod threadM5×0.8
- CushionElastic bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PB Pen-type Cylinder PB6X60R
The AirTAC PB6X60R is a double-acting JIS pen-size mini cylinder engineered for compact, high-frequency small-part motion. It features a slim SUS304 stainless steel round barrel and piston rod, offering excellent durability in damp or mildly corrosive environments while keeping end-of-arm tooling weight to an absolute minimum. Delivering 14.2 N of push force at 0.5 MPa, this 6 mm bore unit is built for tight jigs.
This specific configuration uses an R axial air inlet for clean in-line plumbing and an M5x0.8 port. It operates at speeds from 50-800 mm/s and relies on a fixed TPU bumper at each end to decelerate the stroke. Because there is no sensor magnet, you will need to use external physical stops if position detection is required.
Airtac PB Pen-type Cylinder PB6X60R Technical Specifications
| Model | Airtac PB Pen-type Cylinder PB6X60R |
|---|---|
| Series | PB JIS pen-size mini cylinder |
| Bore size | Ø6 mm |
| Rod diameter | Ø3 mm |
| Stroke | 60 mm |
| Acting type | Double acting |
| Port size | M5×0.8 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 0.7 MPa |
| Proof pressure | 1.2 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 50 – 800 mm/s |
| Cushion | Elastic bumper (both ends) |
| Max standard stroke | Up to 60 mm |
Specifications follow the official AirTAC PB pen-size datasheet. Piston rod and barrel are stainless steel. Confirm bore, stroke and back-cover option against the product label before installation.
Theoretical Output Force (Ø6mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 14.2 N | 10.6 N |
| 0.7 MPa (max) | 19.8 N | 14.8 N |
Values are taken from the AirTAC PB thrust table. Because pull acts on the rod-side annular area, pull force is always lower than push. Actual usable force is reduced by friction — size with a margin.
Model Code: Airtac PB Pen-type Cylinder PB6X60R
| PB | JIS pen-size double-acting mini-cylinder series. |
|---|---|
| 6 | Bore size in mm. |
| ×60 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| CB / U / R | Back cover: CB double clevis, U 90° side inlet, R axial inlet (bore-dependent). |
Mounting accessories: LB, FA, CJ. Related PB-family variants: PSB (single-acting push), PTB (single-acting pull), PBD (double rod), PBJ (adjustable stroke), PBR (front-mount).
Where the Airtac PB Pen-type Cylinder PB6X60R Is Used
PCB Edge Guide Pin
Pushes a spring-loaded guide pin to locate thin printed circuit boards within an SMT pick-and-place fixture without adding bulk to the moving carriage.
Film Dispenser Tensioner
Extends to nudge a delicate tensioning roller on a vertical form-fill-seal machine, maintaining consistent wrapping film alignment at high cycling rates.
Lab Sample Ejector
Ejects lightweight microtiter plates from a centrifuge carousel, using the compact 6 mm body to fit seamlessly between dense spinning racks.
Is the Airtac PB Pen-type Cylinder PB6X60R the Right Cylinder?
When sizing this actuator, plan for a safe working load of about 9 N, which accounts for roughly 60% of the 14.2 N theoretical push at 0.5 MPa to overcome seal friction and ensure smooth travel. If you need to step down, the Ø4 bore provides 6.3 N of push at 0.5 MPa; stepping up to the Ø10 bore yields 39.3 N. Keep in mind that a plain PB cylinder does not hold its position if air pressure drops or the valve is centered, as the piston will drift and the bumper only decelerates near the stroke end. For a fail-safe hold, an external rod lock is required.
Confirm your ordering essentials: 6 mm bore, 60 mm stroke, M5x0.8 port, no magnet, R axial inlet, and no mounting bracket. Note that the Ø3 mm rod is designed purely for coaxial thrust; over this 60 mm stroke, any off-axis load warrants an external linear bearing to prevent binding.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Slim pen body vs. a standard round cylinder
- ✓ Back cover: CB / U / R inlet direction
- ✓ Magnet (S) for sensors?
- ✓ Mounting: LB / FA / CJ or front thread
- ✓ Keep the load coaxial — avoid side load
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 0.7 MPa operating pressure.
- check Keep the load coaxial; avoid side load on the thin rod.
- check Do not dismantle the front or back cover.
- check Fit dust caps to ports during long-term storage.
- check Installation by qualified personnel per AirTAC docs.
Airtac PB Pen-type Cylinder PB6X60R FAQ
This double-acting cylinder delivers a push of 14.2 N and a pull of 10.6 N at 0.5 MPa. At the maximum operating pressure of 0.7 MPa, it provides 19.8 N of push and 14.8 N of pull. It operates between 0.15-0.7 MPa, runs at speeds of 50-800 mm/s, and uses an M5x0.8 port.
It uses a fixed TPU bumper at each end that decelerates the piston over the last few millimeters; it is not adjustable and not a lock. If cycling heavy tooling mass at high speed, meter-out the exhaust or add an external shock absorber. If power is lost, the piston drifts, so an external stop is needed to hold a load.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC PB Pen-Size Cylinders
Request a Quote for Airtac PB Pen-type Cylinder PB6X60R
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.