Airtac SGC Standard Cylinder SGC125X600S
The AirTAC Airtac SGC Standard Cylinder SGC125X600S is a genuine double acting ISO 15552 (orig. ISO 6431) tie-rod air cylinder with a Ø125mm bore and 600mm stroke, G1/2 air ports and adjustable end cushioning. Its large-bore tie-rod build delivers high thrust and drops into standardized ISO 15552 mounting on heavy automation.
- BoreØ125 mm
- Stroke600 mm
- Port sizeG1/2
- Acting typeDouble acting
- Rod threadM27×2.0
- CushionAdjustable, 40 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SGC Standard Cylinder SGC125X600S
Delivering 6136 N of push force at 0.5 MPa, this double-acting ISO 15552 tie-rod cylinder is built for large-bore automation tasks. Four steel tie rods clamp the aluminium barrel to the covers for high structural rigidity, while the two-way piston seal maintains an internal oil reservoir for long mechanical life. Plan for about 3682 N of real work at 0.5 MPa, which translates to lifting roughly 313 kg vertically with a 2:1 safety margin.
Because this SKU includes the -S magnet, it directly supports CMSG, DMSG, and EMSG position switches without further modification. The 125 mm bore uses a G1/2 port and an M27x2.0 rod thread, and you can swap the standard TPU seals for Viton H to push the operating temperature range up to 150 C.
Airtac SGC Standard Cylinder SGC125X600S Technical Specifications
| Model | Airtac SGC Standard Cylinder SGC125X600S |
|---|---|
| Series | SGC ISO 15552 tie-rod cylinder |
| Bore size | Ø125 mm |
| Stroke | 600 mm |
| Acting type | Double acting |
| Port size | G1/2 |
| Rod thread | M27×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Adjustable, 40 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC SGC datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Thread options: PT (blank) / G. TPU seals are not available for the Ø250 bore (NBR / Viton only).
Theoretical Output Force (Ø125mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 6136 N | 5734 N |
| 0.7 MPa | 8590 N | — |
| Max (@1.0 MPa) | 1251 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SGC Standard Cylinder SGC125X600S
| SGC | ISO 15552 tie-rod cylinder (double-acting type). |
|---|---|
| 125 | Bore size in mm (125 / 160 / 200 / 250). |
| ×600 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
SGC-family variants: SGC (double acting), SGCD (double rod), SGCJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / FTC / TCM1 / TCM2. Seals: TPU (blank) / Viton H / NBR N.
Where the Airtac SGC Standard Cylinder SGC125X600S Is Used
Pallet Transfer Diversion
Pushes heavy loaded pallets off a main conveyor line onto a branch spur using its 600 mm reach and 6136 N thrust at 0.5 MPa.
Automated Warehousing Gate
Acts as a long-stroke actuator to open and close large physical security gates or dividers in high-throughput logistics centres.
Press Ejection Mechanism
Ejects formed metal parts from a hydraulic press bed, utilizing the 125 mm bore and adjustable cushions to absorb end-of-stroke impact.
Is the Airtac SGC Standard Cylinder SGC125X600S the Right Cylinder?
Stepping down to a smaller bore is not an option within the SGC family, but moving up to the 160 mm bore raises the 0.5 MPa push force to 10053 N if your application outgrows this 125 mm unit. For the 600 mm stroke, you must account for rod-bending and side loads—use an external guide to support the rod end and prevent premature seal wear.
The built-in -S magnet enables CMSG, DMSG, and EMSG electronic or reed switches for end-of-stroke detection. Remember that a standard cylinder drifts when air is lost or the valve is centred; the adjustable 40 mm air cushions only decelerate the piston near stroke ends, so specify an external rod lock or pilot-operated check valve if the load must be held in place.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Long-stroke side load — support the rod end
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load; support long strokes at the rod end.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SGC Standard Cylinder SGC125X600S FAQ
This 125 mm bore cylinder features a G1/2 air port and an M27x2.0 rod thread. It generates 6136 N push and 5734 N pull at 0.5 MPa, 8590 N push and 8028 N pull at 0.7 MPa, with a theoretical maximum of 1251 kgf at 1.0 MPa.
Yes, it is dimensionally interchangeable per the ISO 15552 mounting interface, so it drops into standard large-bore fixtures like LB foot or TC trunnion brackets. The -S suffix means it has a built-in piston magnet ready for CMSG, DMSG, or EMSG switches.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Made to Order
Large-bore cylinders built to order — confirm lead time.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SGC Cylinders
Request a Quote for Airtac SGC Standard Cylinder SGC125X600S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.