Airtac SGC Standard Cylinder SGC125X650SLB
The AirTAC Airtac SGC Standard Cylinder SGC125X650SLB is a genuine double acting ISO 15552 (orig. ISO 6431) tie-rod air cylinder with a Ø125mm bore and 650mm stroke, G1/2 air ports and adjustable end cushioning. Its large-bore tie-rod build delivers high thrust and drops into standardized ISO 15552 mounting on heavy automation.
- BoreØ125 mm
- Stroke650 mm
- Port sizeG1/2
- Acting typeDouble acting
- Rod threadM27×2.0
- CushionAdjustable, 40 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SGC Standard Cylinder SGC125X650SLB
Delivering 6136 N of push force at 0.5 MPa, this double-acting ISO 15552 tie-rod cylinder handles large-bore automation tasks with ease. Four steel tie rods clamp the aluminum barrel to the covers for high structural rigidity, while the two-way piston seal maintains an internal oil reservoir for long service life. Plan for about 3682 N of real work at 0.5 MPa, which safely lifts roughly 313 kg vertically with a 2:1 margin.
The built-in -S piston magnet directly supports CMSG, DMSG, and EMSG position switches. Because the stroke runs 650 mm, providing external guide support prevents rod bending under side loads. This model uses a G1/2 port, an M27x2.0 rod thread, and a 40 mm adjustable air cushion at both ends to decelerate the payload smoothly.
Airtac SGC Standard Cylinder SGC125X650SLB Technical Specifications
| Model | Airtac SGC Standard Cylinder SGC125X650SLB |
|---|---|
| Series | SGC ISO 15552 tie-rod cylinder |
| Bore size | Ø125 mm |
| Stroke | 650 mm |
| Acting type | Double acting |
| Port size | G1/2 |
| Rod thread | M27×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Adjustable, 40 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC SGC datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Thread options: PT (blank) / G. TPU seals are not available for the Ø250 bore (NBR / Viton only).
Theoretical Output Force (Ø125mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 6136 N | 5734 N |
| 0.7 MPa | 8590 N | — |
| Max (@1.0 MPa) | 1251 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SGC Standard Cylinder SGC125X650SLB
| SGC | ISO 15552 tie-rod cylinder (double-acting type). |
|---|---|
| 125 | Bore size in mm (125 / 160 / 200 / 250). |
| ×650 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
SGC-family variants: SGC (double acting), SGCD (double rod), SGCJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / FTC / TCM1 / TCM2. Seals: TPU (blank) / Viton H / NBR N.
Where the Airtac SGC Standard Cylinder SGC125X650SLB Is Used
Pallet Diversion
Pushes heavy timber pallets sideways onto secondary processing lines using the 6136 N thrust at 0.5 MPa.
Vertical Lift Gate
Raises 300 kg mezzanine safety gates through the 650 mm travel, relying on the -S magnet for top and bottom confirmation.
Press Ejection
Clears formed metal blanks from a 125-ton stamping press, utilizing the 40 mm adjustable cushions to soften end impacts.
Is the Airtac SGC Standard Cylinder SGC125X650SLB the Right Cylinder?
Sizing demands looking both ways: stepping down is not an option as 125 mm is the smallest SGC bore, while moving up to the 160 mm bore increases thrust to 10053 N at 0.5 MPa. The included LB foot mounting bracket matches the ISO 15552 interface, allowing easy integration with standard fixtures. For this 650 mm stroke, add an external linear guide to absorb lateral forces and protect the rod. Remember that standard air cushions only decelerate the piston near stroke end; they do not lock the load. If power drops, the piston drifts, so install an external rod lock or pilot-operated check valve for vertical holding.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Long-stroke side load — support the rod end
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load; support long strokes at the rod end.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SGC Standard Cylinder SGC125X650SLB FAQ
This 125 mm bore cylinder features a G1/2 air port and an M27x2.0 rod thread. It generates 6136 N push and 5734 N pull at 0.5 MPa, 8590 N push and 8028 N pull at 0.7 MPa, with a theoretical maximum of 1251 kgf at 1.0 MPa.
Yes, it is dimensionally interchangeable per the ISO 15552 mounting interface, so standard LB foot brackets and other ISO fixtures fit perfectly. The -S suffix means it has a built-in magnet ready for CMSG, DMSG, or EMSG reed and electronic switches.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Made to Order
Large-bore cylinders built to order — confirm lead time.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SGC Cylinders
Request a Quote for Airtac SGC Standard Cylinder SGC125X650SLB
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.