Airtac SGC Standard Cylinder SGC160X100S
The AirTAC Airtac SGC Standard Cylinder SGC160X100S is a genuine double acting ISO 15552 (orig. ISO 6431) tie-rod air cylinder with a Ø160mm bore and 100mm stroke, G3/4 air ports and adjustable end cushioning. Its large-bore tie-rod build delivers high thrust and drops into standardized ISO 15552 mounting on heavy automation.
- BoreØ160 mm
- Stroke100 mm
- Port sizeG3/4
- Acting typeDouble acting
- Rod threadM36×2.0
- CushionAdjustable, 50 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SGC Standard Cylinder SGC160X100S
Delivering 10053 N of push force at 0.5 MPa, this large-bore double-acting actuator is built around a rigid tie-rod design where four steel rods clamp the aluminum barrel to the covers. The standardized ISO 15552 mounting interface means it drops directly into existing large-bore fixtures, and its two-way piston seal maintains an internal oil reservoir for long service life. Equipped with a G3/4 port and an M36x2.0 rod thread, it integrates smoothly into heavy pneumatic setups.
Because this SKU includes the -S magnet, it supports CMSG, DMSG, and EMSG position switches for closed-loop control. For practical sizing, plan for about 6032 N of real work at 0.5 MPa, which equates to lifting roughly 512 kg vertically with a 2:1 safety margin. You can also specify Viton H seals if your environment demands 0-150 C high-temperature operation.
Airtac SGC Standard Cylinder SGC160X100S Technical Specifications
| Model | Airtac SGC Standard Cylinder SGC160X100S |
|---|---|
| Series | SGC ISO 15552 tie-rod cylinder |
| Bore size | Ø160 mm |
| Stroke | 100 mm |
| Acting type | Double acting |
| Port size | G3/4 |
| Rod thread | M36×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Adjustable, 50 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC SGC datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Thread options: PT (blank) / G. TPU seals are not available for the Ø250 bore (NBR / Viton only).
Theoretical Output Force (Ø160mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 10053 N | 9425 N |
| 0.7 MPa | 14074 N | — |
| Max (@1.0 MPa) | 2050 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SGC Standard Cylinder SGC160X100S
| SGC | ISO 15552 tie-rod cylinder (double-acting type). |
|---|---|
| 160 | Bore size in mm (125 / 160 / 200 / 250). |
| ×100 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
SGC-family variants: SGC (double acting), SGCD (double rod), SGCJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / FTC / TCM1 / TCM2. Seals: TPU (blank) / Viton H / NBR N.
Where the Airtac SGC Standard Cylinder SGC160X100S Is Used
Stamping Press Feeders
Pushes heavy coil stock into a mechanical press, utilizing the 10053 N thrust at 0.5 MPa to overcome material friction and guide resistance.
Pallet Dispenser Pusher
Separates empty pallets from a magazine stack, relying on the 100 mm stroke and 9425 N pull force to retract the heavy carriage reliably.
Injection Mold Ejection
Drives a large mold ejection plate, using the -S magnet and EMSG sensors to confirm part release before the press opens.
Is the Airtac SGC Standard Cylinder SGC160X100S the Right Cylinder?
When sizing this 160 mm bore, verify if the 10053 N push at 0.5 MPa offers enough headroom, or step up to the 200 mm bore (15708 N push) for heavier demands; stepping down to the 125 mm bore yields 6136 N. This 100 mm stroke operates well within the 30-500 mm/s speed range, but remember that a standard cylinder drifts when air is lost or a valve centers, as the adjustable 50 mm air cushions only decelerate the piston near stroke ends rather than locking it. For suspended loads, specify an external rod lock or pilot-operated check valve. The included -S magnet pairs directly with CMSG, DMSG, or EMSG sensors, and mounting options span LB foot, FA flange, or TC trunnion styles.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Long-stroke side load — support the rod end
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load; support long strokes at the rod end.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SGC Standard Cylinder SGC160X100S FAQ
This 160 mm bore cylinder features a G3/4 air port and delivers 10053 N push / 9425 N pull at 0.5 MPa, 14074 N push / 13194 N pull at 0.7 MPa, and a theoretical maximum of 2050 kgf at 1.0 MPa.
Yes, it is dimensionally interchangeable per the ISO 15552 mounting interface, so standard large-bore accessories fit perfectly. The included -S piston magnet allows you to mount CMSG, DMSG, or EMSG switches directly to the barrel.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Made to Order
Large-bore cylinders built to order — confirm lead time.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SGC Cylinders
Request a Quote for Airtac SGC Standard Cylinder SGC160X100S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.